PLCD69 OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • Automatically Memory Storing • Hiding Panel • Preset Equalization • Auxiliary Input Function • Remote Conrol
CONTENTS Installation .....................................................................................................3 DIN Front-Mount (Method A) ..................................................................................3 Installing the unit ...............................................................................................3 Removing the unit .............................................................................................4 DIN Rear-Mount (Method B) ....................
INSTALLATION Notes: DIN FRONT-MOUNT (Method A) • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Installing the unit 1 2 • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. 182 53 3 • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. (Fig. 1) 1.
INSTALLATION Removing the unit 1. 2. 3. 4. Factory-installed radio bracket Car radio mounting bracket Screw After aligning the car radio mounting bracket with the factory-installed radio bracket, tighten the screws (M5x4mm) at 2 places on each side. 5. When fixing factory-installed radio bracket with the screws, use a standard-tipped screwdriver to pry the tabs of the car radio mounting bracket to make them fit into the holes in the factory-installed radio bracket. 6. Movable panel frame 1 2 3 1.
USING THE FRONT PANEL 1. When open the car lock (ACC ON), the panel of the unit will change from State 1 to State 2 (see below), the hidden panel will turn up. 3. Then insert a disc in the disc slot, the panel will automatically turn up to State 2. Press (eject) button again, the panel will turn down to eject the disc. If you don’t insert a disc in again, the panel will automatically turn up about 10 seconds. If you don’t want to wait, press (eject) button, the panel will also turn up. 4.
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR (GREEN) FUSE IGNITION RED SWITCH (B+) SUBWOOFER CABLE (BROWN) MEMORY BACK-UP YELLOW Rch RED FRONT RCA CABLE Lch WHITE GROUND (B–) BLACK (GREY) REAR RCA CABLE POWER ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER Rch RED Lch WHITE BLUE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 6 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION 16 13 4 11 10 26 17 25 12 18 19 8 20 21 14 22 9 15 6 3 24 1 7 2 23 5 the following order: GENERAL OPERATION Volume • ON/OFF When the hiding panel turns up (in State 2), press button (9) to turn on the unit. When system is on, press button (9) to turn off the unit. Bass Treble Balance Fader By pressing volume up button (11) or volume down button (12), it is possible to adjust the desired sound quality.
OPERATION • RESET RESET button (25) must be activated with either a ball point pen or thin metal object. RESET button (25) is to be activated for the following reasons: • SET THE CLOCK Press the DSP button (15), and the clock is shown on the display. Then hold down the button until the clock flashes. Then press the MANU/SKIP button (17) to change hours or MANU/SKIP button (16) to change minutes. - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate.
OPERATION • AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING RADIO OPERATION - Automatic Memory Storing Press AMS button (18) for several seconds, the radio searches from the current frequency and checks the signal strength level until one cycle search is finished. And then 6 strongest stations are stored into the corresponding preset number button. • BAND SELECTION At tuner mode, press LOU/BND button (13) shortly to select the desired band.
OPERATION CD OPERATION Note: • CD OPEN/CLOSE/EJECT When the front panel is in State 2 and the unit is on, press (eject) button (4), the panel will change into State 3 and display the disc slot (5). Then insert a disc into the slot, the panel will automatically turn up. Press (eject) button (4) again to eject the disc. And after about 10 seconds, the panel will turn up. A. Notes on discs: • Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit.
OPERATION REMOTE CONTROL HANDSET 1 7 4 3 8 9 6 5 13 2 12 10 11 14 15 FUNCTION KEYS & CONTROL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 165 (D) x 50 (H) : : : : ± 10 dB ± 10 dB 4 x 60 Watts 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 20 Hz - 20 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. No sound. Sound skips. The operation keys do not work. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown.
www.pyleaudio.
