PLCD19XMR OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • XM Ready Function • Automatic Memory Storing • Slide Down Detachable Panel • Direct Track Access • Program CD Tracks • CD Changer Control • Auxiliary Input Function • Wired Commander Control www.pyleaudio.
CONTENTS Installation .....................................................................................................3 DIN Front-Mount....................................................................................................3 Installing the unit.............................................................................................3 Removing the unit...........................................................................................4 Using the Detachable Front Panel ............
INSTALLATION Notes: TAKE OUT SCREWS BEFORE INSTALLATION • The unit can be installed on the vehicle or the ships. Before install the unit, please remove the two screws. • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Take out screws before installation • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
INSTALLATION Removing the unit 1 6 1 2 5 3 7 4 Front Panel OPEN button (Fig. 2) 2 1. 2. 3. 4. 5. 6. Dashboard Nut (5mm) Spring washer Screw (5x25mm) Screw Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer 1. Before removing the unit, press the OPEN button to slide down the front panel. 2. Lever Insert the levers supplied with the unit into the grooves in the housing as shown in figure until they click.
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel To Reinstall the Front Panel 1. Press the OPEN button, the front panel will slide down. 1. When the panel bracket is in slide down position, insert the front panel into the panel bracket and push the front panel from the middle to slide it up. Open Bottom Button 2. When the front panel slides down, press the bottom button of the front panel upward and pull it out from the panel bracket. Bottom Button 3.
WIRING CONNECTION XM AUDIO CABLE(BLACK) (BLACK) AUDIO R IN (RED) AUDIO L IN (WHITE) XM RECEIVER CONNECTOR SOCKET (BLACK) WIRING REMOTE CONNECTOR SOCKET (BLACK) CD CHANGER CONNECTOR SOCKET FUSE RED RCH WHITE RCH AUX IN CABLE (YELLOW) RED FRONT RCA CABLE (BROWN) ANTENNA CONNECTOR Rch WHITE Lch RED REAR RCA CABLE (GREY) Rch WHITE Lch BLUE RED YELLOW BLACK FRONT Lch SPEAKER REAR Lch SPEAKER WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 6 FRONT Rch SPEAKER REAR
OPERATION CONTROL & FUNCTIONS KEYS 1 8 6 2 3 5 4 7 This unit is a marine rated wired remote control made using a modified controller or similar layout. It is capable of operation specified functions on the marine AM/FM/CD receiver. The body, buttons, controls and display need to be UV and water-resistant. It includes and LCD and an illumination circuit. The flat body should be watertight and the circuit board clear coated. 1 Power button Press the button (1) shortly to turn on/off the head unit.
OPERATION 4 MODE SELECTION button Press the MODE button (4) to step sequentially through the following sources: e.g. radio mode to CD mode to CDC mode to AUX in mode. 5 BAND SELECTION button Press the BAND button (5) to step sequentially through the following bands: FM1, FM2, FM3, AM1, AM2. 6 TRACK/SEARCH/TUNE buttons • STATION SELECTION (FOR RADIO OPERATION) Press / buttons (6) shortly to activate automatic seek function.
INSTALLATION INSTALLATION HARDWARE HOLDER BASE REMOTE MOUNTING BRACKET X1 X1 X1 SCREW (ø4X50) NUT X2 X2 INSTALLATION DIAGRAM 1. First insert the hooks on the base into the slots of the holder to install the base to the holder. 2. Select the proper object, then place the remote mounting bracket on the base and let the object go through the base and the mounting bracket. 3.
OPERATION LOCATION OF KEYS 16 9 11 10 6 12 13 17 19 8 20 1 21 14 22 5 1. DISP 2. AS/PS/ELAPSE 3. / /MUTE 4. EJ 5. DISC SLOT 6. MODE 7. OPEN 8. LIQUIID CRYSTAL DISPLAY 9. PWR 10. SEL/MENU 11. VOL 12. VOL 13. SHIFT/SCAN/XM-MOD 23 24 18 2 25 14. M1~M6 Preset buttons 15. LOUD/DIM 16. CH 17. CH 18. BAND/ENTER 19. M1 MEM (CAT ) 20. M2 PGM (CAT ) 21. M3 RPT 22. M4 SHF 23. M5 SCN 24. M6 25.
OPERATION select different set mode and separately to press VOL button (11) or VOL button (12) to select your requisite as following order. GENERAL OPERATION SWITHCHING ON/OFF THE UNIT Pressing PWR button (9) to switch on or turn off the unit. When system power turns on, the system is returned to previous mode. BEEP ON/OFF FREQ/CLOCK/NO PRI PRIORITY FACEPLATE RELEASE Press OPEN button (7) to slide down the removable faceplate.
OPERATION “FREQ/CLOCK/NO PRI priority” mode. And then you can press VOL button (11) or VOL button (12) to select frequency priority or clock priority or no priority. - When select Frequency Priority: The frequency will appear on the unit all the while. Pressing DISP button (1) while in Frequency Priority will temporarily display clock and then returns to frequency display. - When select Clock Priority: The clock will appear on the unit all the while.
OPERATION until the corresponding preset button number appears. Repeat steps 1 and 2 to program additional stations. - Quick tuning Select the desired band, then press one of the ten preset buttons (14). RADIO OPERATION SWITCHING TO RADIO MODE Press MODE button (6) shortly to select radio mode, the radio mode appears in the display together with the memory band and frequency.
OPERATION STORING PRESET CHANNELS The preset buttons can be used to store channels for convenient access to your favorite channels. - Programming channels 1. Select the desired channel you want to store in memory. 2. Press and hold one of the preset buttons for more than 2 seconds until the corresponding preset button number appears. Repeat steps 1 and 2 to program additional channels. - Quick tuning Shortly press one of the preset buttons to select a preset channel directly. 6.
OPERATION tracks to be programmed. “FULL” will appear on the display. - When the CD is played in programmed order by hold pressing PGM button (20) for several seconds, hold pressing it again for several seconds will exit PGM mode. - When the disc is playing in programmed order, hold pressing MEM button (19) for several seconds will cancel the all programmed content and “CLEAR” appears on the display.
OPERATION DIRECT TRACK ACCESS Pressing number buttons 0~9(14) (i.e. 19~28) can activate DIRECT TRACK ACCESS according to your need. For example, press button (19), and “T-01” will be flashing on the display. Then press button (20), “T-12” will appear and track 12 will be selected to play. If you don’t press any button when “T-01” is flashing. After several seconds, “T-01” doesn’t flash and track 1 is selected to play.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 178 (D) x 50 (H) mm : : : : ± 10 dB ± 10 dB 4 x 50 Watts 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 60 dB : More than 50 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The car ignition switch is not on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
