blu™ 3-Pack POS Unit SETUP GUIDE
General Safety Information........................................... 4 Care and Maintenance.................................................. 5 Certification.................................................................. 5 What’s Included ........................................................... 6 Components Overview.................................................. 7 blu™ 3-Pack POS Setup Guide .......................................
GENERAL SAFETY INFORMATION FOR THE SAFE AND SUCCESSFUL OPERATION OF THIS PRODUCT, PLEASE READ AND FOLLOW THE INFORMATION CONTAINED IN THIS USER MANUAL BEFORE USE. • Do not try to access internal components of any blu™ units as contents may cause electric shock. • For proper operation, use only approved blu™ branded electronics and components as well as specified compatible electronic devices. • Do not place any items between stacked units at any time.
CARE AND MAINTENANCE • Keep blu™ units and all accessories out of reach of children. • Do not use third party power supplies or non-approved adapters with blu™ units. • Do not attempt to open the outer casing of the product. • Do not clean any blu™ units with harsh chemicals and keep blu™ units away from liquids. • Do no expose blu™ units to extreme temperatures. • Do not paint or apply coatings to blu™ units, as you might affect parts or damage internal components.
WHAT’S INCLUDED 1 8 5 2 9 6 3 blu™ 3-Pack LCD Unit blu™ 3-Pack POS Unit SETUP GUIDE SETUP GUIDE 10 7 4 1. 2. 3. 4. 5. blu™ Product Unit blu™ Product Tray (with Starter Kit insert) Setup Guide 60 Watt Power Supply Screwdriver 6. 7. 8. 9. 10.
COMPONENTS OVERVIEW FRONT VIEW 4 1. 2. 3. REAR VIEW 1 6 3 Blue Front Trim Blue Rear Trim Pack Display Fascia 2 5 4. 5. 6.
blu™ 3-Pack POS Unit Setup Guide Installing Display Packs • Remove unit from box and lay flat on the rear side with the display cavity facing upwards. Remove front blue trim as shown in the visual opposite. • Using the screwdriver provided, remove each screw from the front fascia by turning the screw anti-clockwise as shown in the visual opposite. • Carefully remove clear front fascia. • Using the provided doublesided tape, peel one side and press firmly in the center of the rear face of the pack.
• Carefully peel clear film from outer face of clear panel. • When all packs are placed, secure the clear front fascia as shown and secure by replacing screws (Clockwise) as per the visual shown opposite. Note: Do not over tighten screws. Tighten until firm but not OVER tight. • Replace front blue trim as shown in the visual opposite.
Installing Pack Tray • Carefully remove the rear blue trim as shown in the visual opposite. • Insert tray using the guide rails on either side of the unit as shown in the visual opposite. • Once the tray is in position, replace the blue trim to the outer edge as shown in the visual opposite.
Removing Dry Starter Kit Insert • Using the screwdriver provided, remove each screw from the clear fascia by turning the screw anti-clockwise as shown in the visual opposite. • Carefully remove clear fascia. • Remove the Starter Kit insert. • Using the screwdriver provided, fix the fascia panel onto the tray using the screws as shown in the visual opposite.
Filling and Dispensing from Trays • Load packs by inserting into the top opening of each section as per the visual opposite. • Remove packs by pulling out from the bottom opening of each section as per the visual shown opposite.
Inserting POS Advertising • Remove blue trim as shown in the visual opposite. • Using the screwdriver provided, remove each screw from the front fascia by turning the screw anti-clockwise as shown in the visual opposite. • Carefully remove clear front fascia. • Lay POS Advertising over the pack display fascia as shown in the visual opposite.
• Fix clear cover on unit using provided screws as shown in visual opposite. • Replace the blue trim as per the visual opposite. Stacking Units • Units can be stacked on top of each other for multiple displays in a store (NOTE: Units should not be stacked more than 3 high). • Only one unit needs to be connected to the power source.
• Will connect automatically to the bottom units power. • Stacked units should sit directly on top of the bottom unit, with the feet of the top unit ‘nesting’ into the top of the bottom unit as per the visual opposite. Applying Pin Covers • Please ensure that any exposed power connection points are covered by the provided pin covers.
Top Unit Pin Cover Application • Remove one side of the double sided tape and place on the inside of the pin cover. • Once the tape is firmly pressed inside the pin cover, place a pin cover over the pins on the top of the unit as shown in the visual opposite. Bottom Unit Pin Cover Application • Similarly, when tape is applied to the second pin cover, place the second pin cover over the pins on the bottom of the unit as shown in the visual opposite.
TROUBLESHOOTING Damaged Goods • If you receive any damaged/ broken components, please contact online support and complete the Re-Order Process form at repsupport@blu.com Electronic Component Failure • If there are issues involving any electronic components, please contact online support at repsupport@blu.
blu™ Appendix FCC Regulatory Compliance Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
