USB Port Card Reader Quick Installation Guide Ver .A 7002-0005 er.
FCC Compliance To comply with the applicable sections of FCC Rules and Regulations, Parts 68 and 15, please follow these instructions: § Do not connect your modem to a party line or to a coin-operated telephone. § If your modem should cause a problem on the telephone line, it should be disconnected from the line until it can be determined whether the modem or another device on the phone line caused the problem. § Only the manufacturer can make repairs to the modem.
FCC Part 15 Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
§ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. § Consult the dealer or an experienced radio/ TV technician for help. ! Caution Any changes or modifications not expressly approved by the grantee of this device could void the user authority to operate the equipment. FCC Part 68 Notice This equipment complies with Part 68 of the FCC rules.
iv If the telephone company suspects a problem with your telephone line is related to an add-on electronic device, such as your modem, they have the right to temporarily suspend your service. It is your responsibility to remove from the telephone line any malfunctioning electronic communications equipment to avoid damage to the telephone system. If your equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily.
Table of Contents Chapter 1 Introduction ........... 1 Feature ............................................... 1 System Requirements ........................ 1 Package Checklist .............................. 2 Chapter 2 Installations ........... 3 Hardware Installation .......................... 3 Installation Procedures for WindowsTM 98 ..................................... 4 Installation Procedures for WindowsTM 2000 ................................. 6 Installation Procedures for Mac ..........
Chapter 1 Introduction USB Port Card Reader is a small device designed for accessing data from Compact Flash or Smart Media Card. USB Port Card Reader is an easy installation device, with only need a USB interface, then it can be access by any PCs, MAC or any notebooks. USB Port Card Reader provide you a fast and easy data exchange mechanism. Feature: l USB connection for truly plug & play: Compact Flash card, Smart Media Card (option) in one device. l Transfer rate: 500-800 Kb/sec.
2 Chapter 1 Package Checklist The package contains the following items: l USB Port Card Reader. l USB cable. l The USB Port Card Reader Quick Installation Guide and installation CD.
Chapter 2 Installations This chapter describes on how to install and power on your USB Port Card Reader. Hardware Installation step 1: 1:Switch on your computer. step 2: 2:After the computer enter to the win98. Plug the device terminal of the USB cable into the connector, shown as figure 1, The other side of the transmission line has to connect to the USB port of the computer, shown as figure 2.
4 Chapter 2 Installation Procedures for WindowsTM 98 1. When hardware installation complete, Windows 98 will auto detect your USB Port Card Reader, following dialog box will appear, click Next. 2. Select “search for the best driver for you device (Recommended)”, then click Next.
Chapter 2 3. Please insert the “USB Port Card Reader” driver into CD-ROM, select CD-ROM driver or Specify a location, click Next. 4. The following message will appear, click Next. 5. Windows then finish installed all the USB port Card Reader driver, click Finish to complete the installation.
6 Chapter 2 6. Later on, windows will detect another Unknown Device, the following dialog box will need you to click Next for advance installation, the procedure will be as same as previous. Please refer to the previous description (From step 1 to 5 ). Installation Procedures for WindowsTM 2000 1. Once you have completed the hardware installtion, power on you computer. When running Win2000, your system will detect a new device click Next.
Chapter 2 2. Select the “Search for the best driver for your device (Recommended)” option, then click Next. 3. Place the CD containing driver for Win2000 into your CD-ROM drive. Select the “Specify a location” then click Next. 4. Browse the proper location of the driver path, e.g., E:\WIN2000, then click Next. 5. Click Next. 6. The installation has been completed, click Finish. 7. After the installtion you must reboot the computer to validate the new setting.
8 Chapter 2 Installation Procedures for Mac Setup process: 1. Copy two driver files to Macintosh HD/system folder/Extension folder from CD-ROM/MAC. 2. Restart your computer.
