FCC Compliance | To comply with the applicable sections of FCC Rules and Regulations, Parts 68 and 15, please follow these Instructions: | = o noe connect your modem (o a party line or to a coin-operated telephone, «If your modem should cause a problem on the telephone line, it should be disconnected from the line unl it can be determined whether the modem or another device on the phone line caused the problem. Only the manufacturer can make repairs to the modem.
should contact the appropriate electric inspection authority, or electrician, as appropriate. 5 he Load Number{LN) assigned to each terminal device denotes the percentage of the total load to be connected 1 a telephone loop which is used by the device, to prevent overloading. The termination on a poof may consist of any combination of devices subject only to the Requirement that the total of the Toad numbers of all the devices does not exceed 100.
A Permitted artwork for each device is included from which you may prepare any number of Permitted labels subject to the general Instructions on formal size and color quoted on the attached sheet. The Permitted label must be displayed on the product ac all times as proof to purchasers and service personal that the product is able to be legitimately connected to the Telecommute network. The Permitted label may also be shown an the packaging of the product and in the sales literature, as explained in PTC 100.
Chapter 1 introduction The Voice/Fax/Data PCl Modem connects your computer to Internet, and all kinds of BBS, and other popular Fax/Médems. This manual describes the features, procedures of installations, and AT command set...etc. of this modest. Your modem; K 2 PHONE: Phone jack. B LINE: Telephone line jack. | ; MIC: Microphone jack. ia 7 SPK: Speaker {for Stereo only) jack. oly Features LL This modem supports the following communication standards. IT-T is known as CIT. Data # IT-T V.
2. Installation Procedure for Windows 98 Note: Modem;s Win 9x driver is on the CD. (1) When you finish installation of hardware, please power on your PC. Under Win 198, your PC will find a new device and show following message on screen. Please put the bundled Win j9x driver into your CD driver, then Click ; ext;.
(5) The install is complete now, please click 1 Finish ; § rT sus CLM Data Fax Voice 3. Installation of Communication Software Please refer to your software manual when you are installing software. Your software must be configured to communicate with the modem on the same COM port and IRQ line used by the modem. Please refer to your software manual for detail procedures.
disables auto mode, and optionally specifies the lowest and highest connection rates using two sub parameters The nonfat is: Carrier | Modulation Data Rates (bps) 32 v3 9500, 4800 VIB ibis 14400, 1200, 9600, 7200, 4800 33 Vi 33500, 31200; 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000, 9600. 7200, 4800, 2400 SE000, 34667. 520008, 30667, 49333, 48000, 46667, 45333, 42667, 41333, 38667, 37333, 36004, 34667, 33313, 32000, 30667, 29333, 28000 V0 SU Note: V.
Reports modem chip firmware version. Verifies ROM checksum. Reports chip set name. Reserved 3 i Reserved for modem chip hardware configuration. Country code. Speaker Control Speaker is always off. Speaker ON ilium CONNECT. Speaker is always on. . Speaker off during dialing and receiving carrier and tum speaker on during answering. Return to On-Line Data Mode Go on-line. | Go on-line and retrain.
Chapter 3 commands Most people use the communication software programs to tell modem what they want the modem to do. Therefore, you may not use the commands in this chapter, However, if you prefer 10 communicate with your modem directly, you can type the following commands, Please note that when your type appears on the screen, your modem is in a germinal mode” This chapter will be helpful if you like to work in a terminal mode. When you typing commands; K Use the BACKSPACE key to delete typing errors.
(3) Then you can see the following message on screen. Please select i §specify a location; ‘then click ; Browse; lo find the path of modem driver, for example : Cirrus . Then click ; Next 1 § {4) Windows will find the driver of modem.
Chapter 2 Installations This chapter describes the steps how to install and power on your fax modem. 1. Installing your modem card Step! G Turn off your computer. Carefully remove the cover from the computer and select a slot for your modem. Step G Carefully slide the internal modem Into the sot applying with pressure until the modem is completely plugged into the shot. Step CG Replace the slot cover screw to secure the modem and replace the computers cover.
(5) Only terminal equipment approved for connection to the PST may be corrected to the phone port of the modem. communication module (b) Carrier Card (c) Expansion Card (df) Power supply unit or other saucer of excessive voltage Except for the Edge connector which plugs into the hosts expansion slot, clearance distance (Xmm) and creep age distance) as given in the table above must be maintained between the communication card and any other assemblies which use or generate a hazardous voltage.
properly compatible with the modem at the other end of the call and b/. The application using the modem is compatible with the application at the either end of the call. E.g. accessing the Internet requires suitable software in addition to a modem. = This equipment shall not be used in any manner which could constitute a nuisance to other Telecommute customers, . & Some parameters required for compliance with Telecommute; PTC Specifications are dependent on the equipment (PC) associated with this modem.
To be certain of the number of devices you may connect to your line, as determined by the total REMs, you should call your local telephone company to determine the maximum REN for your calling area. If the telephone company suspects a problem with your telephone line is related ta an add-on electronic device, such as your modem, they have the right to temporarily suspend your service.