Z Series PureMix Z6 / Z7 User Guide MAINS WATER
What's Inside What's Inside Introduction ................................................................................................................................. 2 Operation ...................................................................................................................................... 3 Cartridge Replacement ......................................................................................................... 3 Installation ................................................
Operation Operation The Puretec PureMix Inline Water Filter System is designed to run economically for many years, dependent on the initial installation and periodical maintenance. Flush systems for 10 minutes after any period of non-use more than 2 days. The PureMix Z6 Inline Water Filter System is designed to operate with mains water. The PureMix Z7 Inline Water Filter System is designed to operate with mains, rain, harsh and rural water.
Installation Requirements Installation Requirements 1. 15mm (½”) cold water flexi-connector to tap. 2. Water supply pressure: 200 - 520 kPa. Note: Where line pressure exceeds 500 kPa, an approved pressure limiting device must be installed to comply with Australian & New Zealand Plumbing Standards. 3. Water supply temperature: 0° - 38 °C (protect from freezing). Alternative fittings may be required if being connected to anything other than 15 mm (½”) copper pipe. No electrical or drainage requirements.
Installation Procedure 7. Connect the inlet stem adaptor to the supplied pressure limiting valve (multivalve) , then connect the pressure limiting valve to the cartridge head assembly inlet with the supplied piece of high pressure tubing (white). See Fig. 1. Note: The arrow on the head indicating the direction of the water flow. A hose extension kit has been provided if necessary, this can be used to extend the hose either side of the system. Ensure the hose is kink free. 8.
Installation Diagram Figure 2 - Vertical Installation Diagram Existing Mixer Tap Head Assembly 3/8" High Pressure Tubing Pressure Limiting Valve / Multivalve Stem Adaptor Stem Adaptor Z6-R / Z7-R Cartridge 1/2" Brass Nipple from Included Extension Kit Minimum 70 mm clearance for cartridge changes. COLD Extra Braided Hose from Included Extension Kit HOT Braided Hose Note: Allow extra free space around the system to avoid accidental impact.
Installation Diagram Figure 3 - Horizontal Installation Diagram Existing Mixer Tap Pressure Limiting Valve / Multivalve Also 3/8"includes High Pressure Extending Kit Tubing Stem Adaptor Head Assembly Braided Hose Stem Adaptor Minimum 70 mm clearance for cartridge changes. HOT COLD Z6-R / Z7-R Cartridge Also includes Extending Kit Note: Allow extra free space around the system to avoid accidental impact.
Fitting the Cartridge Correctly Figure 4 - Fitting the Cartridge Correctly Ensuring the cartridge is in the correct lock position is critical prior to operating the system. Not being seated in the correct position can cause the locking tabs to shear and damage the head and/or water leakage. When the cartridge is seated in the correct position the arrows on the cartridge and the head will align. Cartridge NOT in the correct position.
Performance Data Cartridge Changeout 1. Shut off water supply and release the water pressure by opening up the tap. 2. Remove all packaging from the new cartridge, including any wraps or caps (if applicable). Replacement cartridge code for Z6 model: Puretec Z6-R. Replacement cartridge code for Z7 model: Puretec Z7-R. 3. Rotate the old cartridge counterclockwise 1/4 turn, pull it out and dispose of it. 4.
Warranty Notes Puretec water care products are designed, manufactured and supported by Puretec Pty Ltd the name you can trust for viable and proven water solutions. The complete range of Puretec products are developed, refined, made to meet and exceed stringent specifications for the worldwide market. Important: Sales of products are subject to our Terms and Conditions which are available upon request. All specifications, information and photos are a guide only and are subject to change without notice.
Warranty Warranty/Australia This warranty is given by Puretec Pty Ltd, ABN 44 164 806 688, 37-43 Brodie Road, Lonsdale SA 5160, telephone no. 1300 140 140 and email at sales@puretec.com.au. This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement or refund for a major failure and to compensation for other reasonably foreseeable loss or damage.
FEB2023
