IF Series Irrigation Filter Range User Guide IRRIGATION
What's Inside What's Inside Puretec Customer Service ................................................................................................... 2 Guidelines and Warnings ..................................................................................................... 3 Preparing Your System ......................................................................................................... 4 Use Guidelines ....................................................................................
Important Information IMPORTANT INFORMATION! Installation Requirements • System Max Pressure Rating : See model specification table. • DO NOT overtighten when connecting the filter to the piping. Too much tape or over tightening may cause the product to split. • Use PTFE thread seal tape on all connections. Use of pipe sealants will void warranty. • Ensure correct inlet/outlet orientation • Use on cold water line only.
Preparing Your System Preparing Your System Puretec systems are designed to run economically for many years, dependent on the initial installation and periodical maintenance Please read all instructions carefully as failures caused by incorrect installation or operation are not covered by warranty On removing your system from its carton you should check all the components to ensure all are present and have not been damaged in transportation. Remove all the packing materials prior to use.
Model Specifications Model Specifications Inlet / Outlet Connections Model Filtration Type Mesh (Micron) Flow Rate Max Pressure IMF034-80S SS Screen 80 (200) 3/4" (20 mm) 5m3/h 600 kPa IMF034-120S SS Screen 120 (125) 3/4" (20 mm) 5m3/h 600 kPa IMF010-40S SS Screen 40 (375) 1" (25 mm) 6m3/h 600 kPa IMF010-80S SS Screen 80 (200) 1" (25 mm) 6m3/h 600 kPa IMF010-120S SS Screen 120 (125) 1" (25 mm) 6m3/h 600 kPa IMF034-80L SS Screen 80 (200) 3/4" (20 mm) 5m3/h 600 kPa IM
Dimensions 113.31 136.58 Dimensions - Mesh Screen Models 178.00 IMF034-80L, IMF034-120L 113.31 136.58 178.00 IMF010-40L, IMF010-80L, IMF010-120L 178.00 IMF034-80S, IMF034-120S, IDF034-120L 204.23 235.04 178.00 IMF010-40S, IMF010-80S, IMF010-120S, IDF010-120 230.00 IMF112-80, IMF112-120, IDF112-120 6 Installation & Operation Manual 248.
Dimensions Dimensions - Disk Filter Models 309.00 557.12 243.56 IDF020-120 243.56 776.12 309.
Maintenance Maintenance To keep the filter in the best working order it is recommended that you follow the maintenance guidelines below. • Perform a visual check of the filter housing and seals once a week. If needed, repair or replace as necessary. • Clean the filter once a month or as required due to pressure drop, when the pressure drop across the filter reaches 0.6 bar (8 psi). • Perform a deep clean at the beginning and end of the irrigation season.
Replacement Parts Cleaning Disk Filters 1. Turn off the inlet feed water. 2. If the line is pressurised, depressurise the line by releasing a tap downstream. 3. Unscrew the filter cap, or if equipped, unfasten the clamp. 4. Remove the cap. 5. Pull out the filter element 6. Loosen the tightening ring at the base of the spine. 7. Pull the spine to decompress the disk stack. 8. Clean the element using pressurised water (i.e.: garden hose).
Troubleshooting Disk Filters Replacement Codes: Ordering Code Description IDR100-120 Irrigation Disk Filter Replacement, 3/4"-1", 120 Mesh IDR112-120 Irrigation Disk Filter Replacement, 1 1/2", 120 Mesh IDR200-120 Irrigation Disk Filter Replacement, 2" Compact, 120 Mesh IDR200S-120 Irrigation Disk Filter Replacement, 2" Super, 120 Mesh Troubleshooting Fault Possible Cause Suggested Action Drop in the outlet pressure. Element fouled. Clean the element. Connection is leaking.
Warranty Notes Puretec water care products are designed, manufactured and supported by Puretec Pty Ltd the name you can trust for viable and proven water solutions. The complete range of Puretec products are developed, refined, made to meet and exceed stringent specifications for the worldwide market. Important: Sales of products are subject to our Terms and Conditions which are available upon request. All specifications, information and photos are a guide only and are subject to change without notice.
FEB2023
