User’s Guide and Warranty Information PurePower 120 Volt models
Contents Table of Contents About the PurePower APS 2 Safety Warnings 3 Installation Inspecting the Equipment 4 PurePower Preparation 5 Activating Up Your PurePower 8 Operation 12 PurePower Maintenance 13 Specifications 14 Troubleshooting 16 Service and Support 17 Audiophile Power Supply • www.audiophileaps.
About the Audiophile APS The PurePower Audio Power Supply The Audiophile Audio Power Supply (APS) provides pure regenerated power for your sensitive home theater and audio equipment. This is accomplished through our double conversion technology. We convert the incoming AC power to produce a clean DC supply, then recreate a new, 60 Hz, 120 volt AC wave form from the DC. We make sure that your system gets the power it was designed for and your amplifiers get the current they need for top performance.
Safety Warnings Safety Warnings Read the following precautions before you install the APS. IMPORTANT SAFTEY INSTRUCTIONS - SAVE THESE INSTRUCTIONS. This manual contains important instructions that you should follow during installation and maintenance of the APS and batteries. Please read all instructions before operating the equipment and save this manual for future reference. DANGER This APS contains LETHAL VOLTAGES. All repairs and service should be preformed by AUTHORIZED SERVICE PERSONNEL ONLY.
Installation Inspecting the Equipment Before installation, please check to ensure that your PurePower APS package is complete and undamaged. If any deficiencies are discovered, please contact your PurePower Dealer. Shipping damage If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of purchase and file a claim for shipping damage. If you discover damage after acceptance, file a claim for concealed damage.
Installation APS Preparation The APS is designed for flexible configurations and can be rack mounted or placed on a shelf or as a standalone cabinet. If you are installing the APS in a rack, follow the instruction in “Rack-Mount Setup”. Standalone / shelf component When you position the APS horizontally on a shelf or in a non-rack style AV equipment stand or enclosure, ensure there is sufficient clearance for airflow through the grilles at front and rear of the unit. Figure 1.
Installation 06 | Pure Power in > Pure Sound out
Installation Rack-Mount The APS can be installed in 19 or 23-inch racks and needs only 2U of rack space. Mounting rails or a rack shelf are required for your Audiophile APS. If rails are not already installed in your rack or included with your APS, contact your PurePower dealer. Use the following procedure to install the APS in a rack: · Place the APS on a flat, stable surface with the front of the APS facing toward you.
Installation Activating your PurePower APS The following steps explain how to install and start the APS. Activating the APS · Plug the components to be supplied into the APS output receptacles. The PurePower APS design allows any outlet to supply digital, analog or power amplifier components. · DO NOT operate electric space heaters with the APS. · Plug the APS power cord into a utility outlet. All front panel indicators flash briefly and the APS conducts a self-test.
Installation Installing optional Power Packs Modules must be installed before powering the APS. CAUTION: A small amount of arcing may occur when connecting a PowerPack Module to the APS. This is normal and will not harm you. Insert the connection cable into the APS battery connector quickly and firmly.
Operation Operation The PurePower Front panel indicates the APS status through the LED indicators. Figure below shows the APS front panel indicators and controls. Figure 15. APS Front Panel Normal Mode During Normal mode, the ~ indicator illuminates and the front panel displays the percentage of APS load capacity being used by your system. (see Figure). The APS monitors and provides power to your system and charges the batteries as needed.
Operation Battery Mode When the APS is operating during a power outage, the battery indicator illuminates. The front panel displays the approximate percentage of battery capacity remaining (see figure 17). When the utility power returns, the APS switches back to Normal mode operation and the batteries recharge. If battery capacity becomes low while in battery mode, the battery indicator flashes indicating approximately three minutes of battery time remaining.
Operation Turning the PurePower On After the APS is connected to a power outlet, it conducts a self-test and enters Standby mode. To turn on the APSoutput power, press the On | button on the front panel. The ~ indicator illuminates and the bar graph indicators display the percentage of available power being supplied by the APS. Starting the PurePower APS on battery To turn on the APS without using utility power, press and hold the On | button for a least four seconds.
APS Maintenance PurePower Maintenance PurePower APS and Battery Care For the best preventive maintenance, keep the area around the APS clean and dust-free. If the atmosphere is very dusty, clean the outside of the system with a vacuum cleaner. For full battery life, keep the APS at an ambient temperature of 21° C (72° F). Storing the APS and Batteries If you store the APS for a long period, recharge the batteries every 12 months by plugging the APS into a power outlet.
Specifications Specifications This section provides the following specifications for the PurePower APS · Electrical input and output · Weights and dimensions · Environmental and safety · Battery Model List PurePower APS Model 500 PurePower APS Model 700 PurePower APS Model 1050 Watts 490 700 1050 Weight Lb. (kg) 34 (15) 34 (15) 50 (23) Dimensions (HxWxD) 3.5 x 17 x 19.5” 3.5 x 17 x 19.5” 3.5 x 17 x 19.
Specifications Environmental and Safety Operating Temperature Optimal battery performance: Storage Temperature Transit Temperature Relative Humidity Operating Altitude Transit Altitude Audible Noise Surge Suppression Safety Conformance Safety Markings EMC (Class B) 0°C to 32°C (32°F to 90°F) 21°C (72°F) 0°C to 25°C (32°F to 77°F) -25°C to 55°C (-13°F to 131°F) 5-90% noncondensing Up to 3,000 meters above sea level Up to 10,000 meters above sea level Less than 20 dBA ANSI C62.
Troubleshooting Troubleshooting your PurePower APS This section contains troubleshooting information and an explanation of APS alarm conditions.
Service & Support Service And Support For setup and support for your PurePower APS, please contact your authorized PurePower Dealer. For warranty service, please contact your authorized dealer or Audiophile APS. All PurePower APS models have a two year swap out warranty for original registered owners. If we are unable to solve a problem with your APS over the phone, we’ll send you a replacement unit. Just return the original in the same packaging with the supplied shipping documentation.
Pure Power in > Pure Sound out • www.audiophileaps.
