HDMI™ CAT Extender Extends 1 HDMI™ Signal over Single CAT with Bi-directional IR pass-through User’s Guide Model no. PT-E-HD10 Designed in Germany Made in Taiwan © 2010 PureLink GmbH. All rights reserved. www.purelink.
Table of Contents Section 1: Getting Started .................................................................................................. 3 1.1 Safety and Notice .................................................................................................. 3 1.2 Introduction .......................................................................................................... 3 1.3 Package Contents ...........................................................................................
Section 1: Getting Started 1.1 Safety and Notice Please read all of these instructions carefully before you use the device. Save this manual for future reference. The PT-E-HD10 HDMI™ CAT Extender Extends 1 HDMI™ Signal over Single CAT with Bi-directional IR pass-through has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the PT-E-HD10 should be used with care.
HDMI signals accordingly, and therefore optimize the transmission distance between source and destination. — Support HDMI Deep Color & full 3D — Extend the transmission up to 60m (200ft) from the HDMI source at HD 1080i or 720p 24-bit — Extend the transmission up to 40m (130ft) from the HDMI source at Full HD 1080p 24-bit — Extend the transmission up to 20m (65ft) from the HDMI source at Full HD 1080p 36-bit — HDCP 1.
1.5 Panel Descriptions FRONT PANEL — PT-E-HD10, transmitting unit (TX) MODE: 0 - EDID Full-HD(1080p@60) - 24bit 2D video & 7.1ch audio 1 - EDID Full-HD(1080p@60) - 24bit 2D video & 2ch audio 2 - EDID Full-HD(1080p@60) - 36bit 2D video & 7.1ch audio 3 - EDID Full-HD(1080p@60) - 36bit 2D video & 2ch audio 4 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video & 7.
FRONT PANEL — PT-E-HD10, receiving unit (RX) HDMI OUT: Connect to a HDMI display with a HDMI male-male cable here. SIGNAL LEVEL: Adjust the equalization control to the received HDMI signals. The HDMI signal level varies from MAX (strongest) to MIN (weakest) for respective transmission length from longest possible range to short distance. Please adjust the signal level from MIN to MAX and stop turning the rotary switch whenever the audio/video is playing normally.
1.6 IR Pass-through IR Extenders IR Blaster IR Receiver IR Sockets IR Blaster: Plug in the IR blaster here to emit all IR command signals received from the IR receiver to control the HDMI source devices. IR Receiver: Plug in the IR receiver here to receive all IR command signals from the IR remote controls of the HDMI source devices. Wrongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of the IR extenders.
1.7 Installation 1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit PT-E-HD10-TX 2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit PT-E-HD10-RX. 3. Connect IR Blaster/Receiver to both TX and RX units. 4. Connect a Cat-5/5e/6 cable between the transmitting and receiving units. 5. Make sure this Cat-5/5e/6 cable is tightly connected and not loose. 6. Plug in 5V DC power supply unit to the power jack of the receiving unit PT-E-HD10-RX.
Section 2: Specifications Item Units Unit Description HDMI Compliance HDCP Compliance Video Bandwidth Supported Resolutions Resolution and Distance (8-bit) Audio Support Equalization Input TMDS Signal Input DDC Signal ESD Protection Input Output HDMI Connector RJ45 Connector 3.5mm Connector Rotary Switch Dimensions Description Transmitting unit of PT-E-HD10 Receiving unit of PT-E-HD10 Transmitter Receiver HDMI Deep Color & full 3D Yes Single-link 225MHz [6.
Section 3: Notice 1. When adjusting the signal level on the receiver unit, please dial the rotary control switch from MIN to MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may cause overpowering issue that would shorten the product life significantly! 2. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI or HDMI display EDID information. 3.
Section 4: Performance Guide Performance rating Wiring Solid Stranded Type of CAT5/6 cable Shielding CAT5 Unshielded (UTP) Shielded (STP) CAT5e CAT6 Unshielded (UTP) Shielded (STP) Termination Please use EIA/TIA-568-B termination (T568B) at any time www.purelink.
www.purelink.
