MX -800 Owner’s Manual 8 x 8 Digital Modular Matrix Router PureLink TM 535 East Crescent Ave Ramsey, NJ 07446 Tel: 201.488.3232 Fax: 201.621.6118 Website : www.purelinkav.com E-mail : info@purelinkav.com For Technical Support Contact us at support@purelinkav.
PureLink by Dtrovision Table of Contents 1. Product Overview Page. 1.1 Safety Precautions 3 1.2 Introduction 4 1.3 Part Names & Reference 5 1.4 Installation 7 2. Product Features 2.1 Key Functions 8 2.2 Features & Specifications 10 3. Operational Guidelines 3.1 “MAIN MENU” User Guide 11 4. Communication Code Configuration 4.1 RS-232C(COM) COMMUNICATION CODE SET-UP 16 4.2 LAN(TCP/IP) COMMUNICATION CODE SET-UP 24 4.3 Connector Pin Assignment 26 5. Additional Information 5.
PureLink by Dtrovision 1. Product Overview 1.1 Safety Precautions - Always use the correct external power supply (indicated on the product label) when operating this unit. - Please refrain from using frayed power cords and damaged wall outlets. - Mishandling of this product may lead to a fire or explosion hazard. - Do not place any heavy objects or equipment on top of the unit. - Keep away from wet, magnetic, and flammable surfaces or substances.
PureLink by Dtrovision 1.2 Introduction The MX-800 matrix router supports DVI 1.0, HDMI Ver1.3, and HDSDI interface settings in a single unit. The modular input/output ports allow users to connect multiple displays to the router. The MX-800 features a switching mechanism that splits signals from 8 channels to any designated output port. Through channel-input configuration, the MX-800 can recognize up to 32 DVI, HDMI, and HDSDI signals and send them to 8 output ports on command. DVI 1.0 and HDMI Ver. 1.
PureLink by Dtrovision 1.3 Part Names & Reference Front Panel: POWER: Main power switch ON / OFF DISPLAY: View menu and system mode RESET: Revert the matrix router to its original settings.
PureLink by Dtrovision Back Panel DC 12V: Power supply (DC +12V) input port LAN: LAN (TCP/IP) input port RS-232 C: RS-232C input port INPUT SLOT : DVI, HDSDI , CAT-5, OPTICAL ports (IN1~8) OUTPUT SLOT : DVI, HDSDI , CAT-5, OPTICAL ports (OUT1~4)x2 EA 6
PureLink by Dtrovision 1.4 Installation Guidelines and Procedures 1.
PureLink by Dtrovision 2. Product Features 2-1. Key Functions The MX-800 matrix router is compliant with DVI 1.0, HDMI V1.3, and HDSDI. The backpane card slot design allows users to create a customized digital interface for connecting multiple display sources. The MX-800 is an 8-input router with the ability to switch multiple signals to any designated output port, as well as distribute a single input source to multiple output ports.
PureLink by Dtrovision 2-Levels: 3-Levels: 9
PureLink by Dtrovision 2. System Diagram The figure below illustrates a connectivity diagram. Input signals can be switched manually through the front panel or through external control sources (IR, RS-232C, LAN (TCP/IP)), and distributed to any combination of designated output ports. DVI MATRIX ROUTER BLOCK DIAGRAM DVI MATRIX ROUTER INPUT/OUTPUT CONFIGURATION 2-2 Features & Specifications Signal Type : TMDS SIGNAL , DIGITAL R.G.B. & DIGITAL AUDIO Data Transmission Speed : UP TO 2.
PureLink by Dtrovision 3. Operational Guidelines 3.1 MAIN MENU User Guide Turn the power switch on Once all channel indicator lights are on, the first step is complete 1. Initial page on the LCD display 2. Channel View and Input Selection IN / OUT indicates connection status Press the IN / OUT KEY to display each channel’s connection status and video resolution Press the CANCEL KEY to return to the initial screen 3. MX-800 MAIN MENU 1 . C R E A T E 2 . P R E S E T 3 .
PureLink by Dtrovision 6. SYSTEM INFO 7. EDID 8. SYSTEM CONFIG Press the ENTER KEY to select an option. Press the CANCLE KEY to return to the main menu 4. CREATE MENU - P I N / O r e s s u t A C n R y E A T E I n p u - T Select an INPUT channel Press the IN / OUT KEY to set a channel Press the ENTER KEY to save or switch input channels Press CANCEL to reverse a selection and return to the previous screen 5. PRESET MENU - P R E S E T - 1 .
PureLink by Dtrovision Create up to 20 PRODUCT ID’s Set : Displays current number or PRODUCT ID’s Edit : Use the UP / DOWN KEY to select the ID and press ENTER to edit or save. Press CANCEL to reverse selection and return to the previous screen 7.
PureLink by Dtrovision 1 . M a i n S l o T 2 . I n p u S l o t 3 . O u t 1 S l o T ( 1 ~ 4 ) 4 . O u t 2 S l o T ( 5 ~ 8 ) t Displays the firmware version associated with each SLOT. Use the UP / DOWN KEY to select from menu and press ENTER to continue. Press CANCEL to reverse selection and return to the previous screen. 10. EDID MENU 1 . E x t E d i d L o a d 2 . I n t E d i d L o a d 3 .
PureLink by Dtrovision - S Y S T E M h i S 1 . S w i t c 2 . I n u t p C O N F I G n g D e l a e l c t e Y Switching Delay: controlling channel conversion speed Fast: quickest conversion (DVI or 2CH HDMI) Normal: 2-3 sec. delay Slow: 3-5 sec. delay Switching delay may vary with each monitor or TV source. If the video or audio is not displaying properly, adjusting the conversion speed may help correct it. Input Select: choosing the input port.
PureLink by Dtrovision 4. Communication Code Configuration 4-1.COMMAND LINE OPERATIONS ■ Control Programmer’s Guide (Code Structure and Examples) This section is designed for programmers who wish to create their own control programs using the command code. All Pure Link digital matrix routers provide a simple character stream control used by external control devices attached to a Pure Link device.
PureLink by Dtrovision Ex 1) Command (Connect Input 1 to Output 1) *255CI01O01! Ack value *255sC I01O01! Ex 2) Command (Check Input connection status on Output 3) *255?O03! Ack Value *255s? I03O03! General Rules for Command Codes The commands are coded in ASCII and HEXA. Please refer to Table 3.1 on pg. 18 for detailed descriptions of keys and functions.
PureLink by Dtrovision Table 3.1 Command Codes Characters Table The table below shows command code characters (keys), which are used to generate control commands, their functions, and short function descriptions.
PureLink by Dtrovision 0x49 I 0x69 i ?version Specifies a range of numbers in Range entries containing multiple numbers Router ID check command; check Router ID check Firmware router’s current ID number version 1 1 Firmware version check command; *255?version! check Baud rate sting command; *255@001! → 19200 0x40 @ Baud rate setting *255@002! → 38400 *255@003! → 57600 *255@004! Network → 115200 configuration setting command: - IP Setting *255NIP125.135.199.
PureLink by Dtrovision Ack (Acknowledge) Value Response Table The following table shows ack value response characters along with their descriptions and meanings, which may appear instead of the initially entered character or number. If these characters appear, all or part of the command has not been executed. Table 3.2 Descriptions of Acknowledge (ACK) Signals Ack value Description Input 1 is not connected No information in each channel.
PureLink by Dtrovision For example, the command code *255CI01O01! can be interpreted as follows: (*) Starting the command code (255) Router ID is 255 (C) Create connection on (I01) Input 01 to (O01) Output 01 (!) take the command. For a complete list of command characters and their functions, see examples below. To connect a switch: 1. Enter the Connect command below. Replace the “#”s with the input and output number(s).
PureLink by Dtrovision *255ACI01O01-07! Connect Input 1 to Output 1, 2, 3, 4, 5, 6, and 7 4-1.2 Disconnecting Switches The characters and numbers in a Disconnect command tell the system which input or output to disconnect. The “D” key initiates a Disconnect command for routing a switch. The characters and numbers that follow the “D” command tell the system that inputs and outputs to disconnect.
PureLink by Dtrovision *255ADALLIO! Disconnects all inputs and outputs 4-1.3 Connection Status Check A connection status can be checked to confirm that the switch has been correctly executed or to confirm correct routing to multiple outputs. The characters and numbers in a status command tell the system which input or output to check. 1. Enter the Connection status check command below. Replace the “#”s with the input and output number(s).
PureLink by Dtrovision 4-1.6 Baud Rate Setting User can set baud rate for RS-232 command control. 1. Enter the Baud rate setting command below. Replace the “#”s with the input and output number(s).
PureLink by Dtrovision Function Key On/Off: User can enable or disable the function key located on physical router’s front panel. Example: Command Codes Action *255K000! Function key On/Off * When using MX-800’s HCIS8 input board, there will be two different types (HDMI & CAT5) of 8 input ports and they are selectable via front panel control or sending a command code.
PureLink by Dtrovision Message indicating TELNET connection will appear *255I000! *255sI Router ID 255* Router ID verification command code Send “ *255I000! ” Router will send response: “ *255sI Router ID 255” 4-2.2 Using HTTP protocol with LAN(TCP/IP - Control PC Search Searching data for channel configuration Character train should begin with “LCD.CGI” to “O01=I08” to Output 01 = Input 8. The sequence and size of the character train must be the same.
PureLink by Dtrovision - Control PC Transmission Information from each channel that needs to be sent must be extracted to prevent the entire Explore html data from being transmitted. - 8:8 html transmitting Run Explorer and enter the newly configured IP address to open the channel configuration window above. Select desired channel and click SEND to change the channel.
PureLink by Dtrovision 4-3 Connector Pin Assignment Power Input Part Name Power Jack RS-232C Input Part Name D-SUB 9-Pin Connector LAN Connector Part Name RJ-45 8-Pin Connector Pin 1 2 3 4 Description VCC( DC12V) VCC(DC12V) GND GND Remarks Pin 1 2 3 4 5 6 7 8 9 Description Not used Rx D Tx D Not used GND Not used Not used Not used Not used Remarks Pin 1 2 3 4 5 6 7 8 Description Transmit data (+) Transmit data (-) Receive data(+) Not used Not used Receive data(-) Not used Not used Remarks 28
PureLink by Dtrovision 5. Additional Information Manufacturer’s Warranty (2-Year) Dtrovision warrants this MX-800 modular matrix router to be free from defects in workmanship and materials, under normal use and service, for a period of two (2) year from the date of purchase from Dtrovision or its authorized resellers. If the product does not operate as warranted during the applicable warranty period, Dtrovision shall, at its option and expense, execute one of the following as necessary: 1.
