M3700 Pure SIP Gateway User Manual Version: 11.0 Firmware: 1.10 Update: 2006/05/12 DCC NO.
M3700 user manual Contents 1. Safety Instructions.................................................................................. 7 2. Preface..................................................................................................... 7 2.1 What is SIP ..........................................................................................................7 2.1.1 2.1.2 SIP Clients..............................................................................................................
8.1 Dialing Plan........................................................................................................38 8.1.1 8.1.2 8.2 8.3 8.4 8.5 8.6 8.7 Dialing Method...................................................................................................... 38 Dial In Rewriting Rule ........................................................................................... 41 Call Forward ..................................................................................................
M3700 user manual Change History: Software Version 1.10 Incoming call to FXO can Incoming call can be forward to other SIP destination. Please refer to be forwarded 9.11 CHANNEL Add digit map function Digit map controls the call route from FXS port. Please refer to 8.1 Dialing Plan RFC2833 is able to send This function is workable at this version Flash DTMF for G.
of 2833 DTMF for Codec-723 Change default value of Default value of RFC 2833 DTMF is changed from Disable to RFC 2833 DTMF Negotiate Change History: Software Version 1.07 Hot Line support M3700 is connected to M4600B SIP Line or other SIP device automatically when calling side picks up phone Change History: Software Version 1.06 NAT signaling keep alive M3700 can send Dummy Packet to SIP Proxy to insure the connection function is alive if the connection need to pass through NAT.
M3700 user manual generated automatically Add SIP-based T.38 Standard SIP-based T.38 is applied. T.38 Proprietary is not retained protocol Add Route control Default route call to outbound proxy if outbound proxy is enabled and Registrar is disabled. Change History: Software Version 1.
New Auto Answer function Disable Auto Answer, Auto Answer without PIN code, Auto Answer for Inbound transit call to with PIN code for inbound transit call control. SIP Interpret T.38 and G.711 Explain the timing for T.38 and G.711 using in products FAX operation Interpret port seizure When make a non-SIP call, those preference will decide which port preference for that the call will go. VOICE/FAX on FXO and FXS port.
M3700 user manual 1. Safety Instructions WARNING 1. Do not attempt to service the product yourself. Any servicing of this product should be referred to qualified service personnel. 2. To avoid electric shock, do not put your finger, pin, wire, or any other metal objects into vents and gaps. 3. To avoid accidental fire or electric shock, do not twist power cord or place it under heavy objects. 4.
It support SIP standard and can register to SIP Proxy. If wireless LAN connection keeps, the Phone can make calls in certain range without wiring. 2.1.2 SIP Servers SIP servers include the following: (1) Proxy server—The proxy server is an intermediate device that receives SIP requests from a client and then forwards the requests on the client's behalf. Basically, proxy servers receive SIP messages and forward them to the next SIP server in the network.
M3700 user manual 3. Package Contents The M3700 Gateway X 1 Power Core X 1 Accessories for fixing support X 1 System CD-ROM X 1 5 IDC Connector X 4 RJ-45 Ethernet Cable X 1 RJ-11 Telephone Cable X 1 (For 3708/3716) (For 3708/3716) Rubber footer 4. Panel Descriptions 4.1 Front Panel REGISTERED STUN M3716 Front Panel REGISTERED STUN M3708 Front Panel M3704 Front Panel M3702 Front Panel 9 DCC NO.
4.2 Rear Panel There is a button on the rear panel of gateway for special maintenance. Please don’t touch this button under normal operation.
M3700 user manual M3702A Rear Panel M3702B Rear Panel 4.3 LED Indicators LED Label Description 10/100 LNK/ACT On Link up Off Link down Flash Sending/Receiving data packets On (LNK is on) 100Mbps Off (LNK is on) 10Mbps On Off hook Off On hook Flash Ringing out On Line is active Off Line is inactive Flash Ringing in Ethernet 100Mbps LOOP/RING FXS FXO Device Alarm The red light “On” indicates that system has some problem; please contact your vender.
4.4 Connectors Ports Label Description Voice Ports FXS Connects to a telephone set or fax machine FXO Ethernet Connects to the phone line LAN/Internet RJ-45 connector Ports MDI-X connects to a Modem PC RJ-45 connector MDI connects to a PC Console Port Console RJ-45 connector/RS-232 Interface (Only 3704/3708/3716) 4.4.
M3700 user manual If Console cable is not available, run Telnet in PC for connection is OK. 4.5 IDC Connectors (Only for 3708/3716) IDC connector is used for the voice interface (FXS and FXO) on the frame model. IDC connector can easily connect PBX line and telephone wire together to the gateway. No special tools are required; please follow the instruction to install: (Remarks: For IDC connector, it’s better to use No. 24 wire, e.g.
5. Information required before Installation You need to prepare the following information before installing the gateway. 5.1 IP Address The gateway requires an IP address for operation. Before installation you need to know how to obtain an IP address from your local ISP. Static IP, DHCP or PPPoE can be used. The following table helps you to decide what information you need. If your ISP offers static IP, you may need to obtain an IP from MIS personnel in order to prevent an IP conflict.
M3700 user manual 5.2 SIP Information Before configuring SIP, the M3700 requires SIP information for operation. The following table helps you to decide what information you need. Items Description 1. SIP Proxy If you want to make SIP calls through SIP proxy server, you will need to know the IP address or domain name of SIP proxy server. The proxy server is an intermediate device that receives SIP requests from a client and then forwards the requests on the client's behalf.
2. Configure IP address of gateway. 3. Enter into the WEB page. 4. Plan and configure the channels into SIP entity. (if needs. By default, all channels joins Entity 1) 5. Configure SIP proxy and registrar information. 6. Configure SIP entity information. 7. Configure Outbound Authentication (If needs). 8. Configure STUN (If your gateway is behind NAT). 9. Check the SIP entity if is registered successful. 10. Configure Phone book (If needs) 11. Make a SIP call. 6.
M3700 6.1.2 user manual System console settings (Only 3704/3708/3716) The Instructions below is to set Region ID from Console terminal or Telnet (For Telnet, From Windows, Start Æ Run Æ Telnet 192.168.0.2 (192.168.0.2 is the default IP of this machine) (In the example, the Region ID is changed to 07 for China) SIP-RG>enable SIP-RG #configure Enter configuration commands, one per line.
6.2.1 Static IP Mode The following table shows an example. IP Address 210.67.96.121 Subnet Mask 255.255.255.248 Default Gateway 210.67.96.120 Web Management 123 Password Using the information contained in the example above. The procedure is as follows: 1. Connect the unit to a suitable Power source. 2. Connect a traditional phone set to the “FXS” connector located on the rear panel. 3. When the CPU/ACT light is on, pick up the phone to hear the dialing tone. 4.
M3700 6.2.2 user manual DHCP Mode 1. Connect the unit to a suitable Power source. 2. Connect a traditional phone set to the “FXS” connector located on the rear panel. 3. When the CPU/ACT light is on, pick up the phone to hear the dialing tone. 4. ##0000 ; you should hear three short tones. 5. 011# ; the digit “0” is used to enable “DHCP” IP mode. 6. 15123# 7. 981# ; “123” is the web management password. ; Warm-restarts. 8. Hang up the phone. The system should now restart.
can find them at section 12.4 Mapping table of characters used in PPPoE. Example user name：83721@hinet.net，Password：123ab，The procedure is below 1. Connect the phone to the unit 2. When CPU/ACT is light, pick up the phone and press ；You will hear 3 short tones. 3. ##0000 4. 0938333732314068696*465742*46*46574# ；Set user name：83721@hinet.net 5. 103132336162# ；Set password is 123ab 6. 981# ；Save and restart. 6.2.3.2 2.
M3700 user manual 3. When the CPU/ACT light is on, pick up the phone. You should hear the dialing tone. 4. ##0000 ; you should hear three short tones. 5. 15123 ; “123” is the web management password. 6. 010# ; “0” is to enable “manual” IP mode. 7. 02192*168*0*2# ; IP address. 8. 03255*255*255*0# ; Subnet Mask . 9. 981# ; Used to restart the unit. 10. Hang up the phone to complete the configuration.
After you have completed the PC’s IP address setting, you will be required to restart the PC in order for the new settings to take effect. Step 3: Using the browser to configure the PPPoE Parameters of the gateway. On the PC that is connected to the unit, enter the unit’s IP address (Default 192.168.0.2) and press enter. The unit will then prompt you with a dialogue box requesting that you enter a password.
M3700 user manual 6.2.3.4 Upon entering the web based configuration interface. Click on “IP SETTING” at the top of the page and you will see the page as shown in the following image. Select PPPoE from the “IP State” pull down menu. Fill in the “Account”, “Password”, and “Confirm Password” under the PPPoE Settings. You can obtain this information from your ISP. Click on the Apply button. Click the “BASIC” button at the top to go to the BASIC page and select “Warm Start” to restart the gateway.
Web Folder: BASIC\ 6 Click the “Apply” button to apply any changes. 5 At this stage, your unit should be able to use PPPoE to access the Internet. However, if you configured a wrong account number or password, your unit cannot access the Internet. You are not able to use PC to access unit by using the IP address of 192.168.0.2 because unit has been set in PPPoE mode. You have to use phone set to configure unit back to fix IP mode (##0000 010#) and use PC browser to configure correct parameters.
M3700 user manual 7. SIP Configuration M3700 not only can make regular PSTN calls, it also can communicate with IP Phones or Soft-Phones by using SIP protocol. This section shows you what parameters you need to configure for SIP calls and how to make the SIP calls. SoftPhone (Notebook／ PC) M3704 M3702/3704 (SIP) IP Cisco IP Phone Notice: These configurations on WEB page, after select or input value in the field, please press “Apply” button to save and confirm the setting.
7.1 Channels and SIP entity Many Channels can be assigned as one SIP Entity. Single Channel also can be assign as one SIP Entity. Application example: As the figure below, Channel 1-3 belongs to SIP Entity 1: 001@abc.com. Channel 4 and Channel 5 belongs to SIP Entity 2: 002@abc.com. and Channel 6-8 belongs to SIP Entity 3: 003@abc.com. When other device under SIP network dial into 001@abc.com, the phone connect to Channel 1 is ringing.
M3700 user manual Notice: Each channel must belong to a SIP entity. 7.2 SIP Proxy and Registrar Parameters You need to configure IP address or Domain name of Registrar and Outbound Proxy server (optional), please check the information is right. SIP service provider will give you an IP address or Domain name of Registrar and Outbound proxy when you apply for the service. Configuration WEB Page: ADVANCED\SIP COMMOM Notice: Generally speaking, Registrar and Outbound Proxy server is same.
7.3 SIP Entity SIP service provider will assign one or more SIP accounts for you when you apply for the service. In standard, the SIP account is called ‘Public Address’, so you need to configure the account information in ‘Public Address’ item. The format is like an E-mail address such as mary@abc.com. The Public Address will be generated automatically with the format below if user keeps the Public Address empty. "Default account's username" @ "Registrar" if you had enter the information below 1.
M3700 user manual "Realm" is a kind of verification for SIP Outbound Authentication. If SIP service provider does not provides this information. The gateway will create a default Realm (by string USER-UNSPECIFIED-REALM) automatically with your Username and Password mentioned on last section for SIP Outbound Authentication. If there are more than one SIP entity is registered on this gateway. The gateway creates Realm for each entity. The default Realm helps you to register the SIP server successfully.
2. If no useable free STUN Server available, for most of ITSP (Internet Telephony Service Provider), their Outbound Proxy Server supports Media Relay, device under NAT can penetrate NAT without configuration. 3. STUN does not support Symmetric NAT. STUN Server NAT Device (Router, IP Internet sharing device) NAT WAN IP Configuration WEB Page: ADVANCED\STUN You can enable and disable the service on WEB page.
M3700 user manual 7.6 Check SIP entity Status You can use the WEB page to check the SIP entity is registered successful or unsuccessful. WEB Page: ADVANCED\SIP COMMOM If the status shows “REGISTERED” means successful, otherwise means fail; please notice that. When you find the registration is fail, first check the “Registrar Setting” configuration is normal, or not “Enable”. Then check the “Public Address” and “Outbound Authentication” configuration is in normal status.
Configuration WEB page: PHONEBOOK \ 7.7.2 Hotline Function A new Hotline function is added for M3700 Firmware Version 1.07 or above When hotline function is enabled, the FXS channel is connected to specified SIP device or M4600B SIP Line (if the M3700 is configured and register to M4600B SIP Line as a client) automatically when user of M3700 FXS channel picks up hand-set.
M3700 user manual Hotline mapping table Channel (FXS) only Index Number Description 1st FXS channel 1 Index number “1” maps the 1st FXS channel 2nd FXS channel 2 Index number “2” maps the 2nd FXS channel …. …. … 16th FXS channel 16 Index number “16” maps the 16th FXS channel Available Hotline index number Model Available Hotline Index Number M3702A 1 M3702B 1, 2 M3704A 1, 2 M3704B 1, 2, 3, 4 M3704C None M3704D 1, 2, 3 M3708 Depends on module used.
Index Public Address Port Via Proxy Description 1 01@61.220.145.70 5060 No 2 73797@fwd.pulver.com 5060 Yes 100 jack@fwd.pulver.com 5060 Yes Channel 1 Hotline to 01@61.220.145.70 without proxy Channel 2 Hotline to 73797@fwd.pulver.com by proxy, No hotline function for channel 200 mike@fwd.pulver.com 5060 Yes 3, 4 to dial 300 Jason@fwd.pulver.com 5060 Yes User of 1st FXS channel picks up hand set, and then 01@61.220.145.
M3700 user manual 7.8 Make SIP Calls After you have configured the SIP phone on the SIP phone book, you can easily make SIP calls. You can select one way to make SIP call following these ways: Standard Call: Dial +<#>. 1. Compare dialing plan, check the number if it is in setting. Example 050. 2. If the number is in setting, send the call to proxy. If the calls does not match dialing plan or the registration to the proxy is fail, then the call will be sent to PSTN. 3.
Notice: If you do not want to dial “#” after numbers, please configure the ‘Dial Ending Time’ item. After the seconds configured here, the call will be sent automatically. WEB Page: ADVANCED\GENERAL 7.
M3700 user manual Dial Inbound Transit Call when Auto Answer is configured as Enable w/ PIN code This Auto Answer mode provides security control for the Inbound Transit call Please dial the number below after the second dial tone: 1. PIN code + ‘#’+ SIP Number + ‘#’, Example: 7742#73797# 2. PIN code + ‘#’+ ‘#’ + Index Number + ‘#’, or Example: 7742##123# If you still need to make a call to the FXS port of this gateway, please press "*" to seize a free FXS port. Notice for the Inbound Transit Call 1.
Making SIP calls without proxy server: The SIP protocol allows you to make SIP calls directly to the destination number without through the proxy server. You can simply dial the SIP number to connect other SIP gateway. The typical example is: 413189@61.220.145.70. mailto: Other SIP gateway that had already configured 413189@61.220.145.70 in Phone Book can connect this gateway by number 413189 without routing through SIP Proxy.
M3700 user manual 8.1.1.1 Dialing Plan Entry "X" means all calls will be sent to SIP proxy, if the SIP call is fail, it is disconnected. Only if the registration to SIP Proxy is failed, then the gateway will try to connect the number by PSTN. Registraton of SIP Proxy can be configured on Web Page: SIP Common. Please refer to 9.
Transparent (with Digitmap) Web Folder: ADVANCED\DIALING PLAN Then you are able to use the transparent function with digitmap. Transparent means all numbers user dials are sent to SIP proxy server and all number that controls M3700 is disabled, including the end code # of each dialing. By this way, all numbers user dials compare with the digitmap. When the number dialed matches the digit map, the number send to Proxy Server immediately without waiting dial ending time.
M3700 user manual previous digit + # or 8 are send to proxy server without waiting dial ending time *2XX Number that match * +2 + any digit + any digit are send to proxy server without waiting dial ending time 8.1.2 Dial In Rewriting Rule Number dialed from M3700 can be converted to different number and sent to SIP Proxy. User can pre-define maximum 10 sets of prefix rewriting rule to convert the number that user dials before build the connection to SIP Proxy.
Country Code + Area Code + Phone No., and then sent to proxy, and prefix phone number 0204 is forbidden. Pattern Rewrite X means any digits. ! means the call is terminated. If the prefix number dials from user are 001~009, then the 3 digits are removed. For example, if user dials 00x 0028621123456, then the system dials 86211123456 to build SIP call. If the prefix number dials from user are 0, then the digit is replaced with 886.
M3700 user manual If Auto Answer function is enabled, Incoming PSTN call dials "*" to seize a free FXS port after second dial tone. The call is not forwarded even the seized FXS port is part of Call Forward SIP Entity. If Auto Answer function is set to Forward to SIP, Incoming PSTN call is forward to new destination configured in the entity that this channel belongs to. Configuration WEB page: ADVANCED\SIP COMMOM Phone Set: Please refer to section Appendix A: Phone-Set Command. 8.
1. Web folder: “Channel” Enable T.38 Fax Relay support. Configure it to Yes 2. Warm-Restart the system Note: For FAX transmission, two gateways will change to SIP-Based T.38 Protocol automatically if both sides support SIP-based T.38. Note: If M3700 connects different SIP devices, some have T.38, but some use G.711 codec only, then user should enable G.711 codec support for FAX. Setup method is listed below: 1. The same step as above set Connect Device to Fax 2.
M3700 VOICE port Select VOICE port only user manual From the lowest port number upward FAX port Select FAX port only From the lowest port number upward 2. Outbound to PSTN For the calls from FXS to FXO, the ports of the same "Connect Device" type will be the prior selection for the calls. If there is no correct configured port is available, it will ignore the "Connect Device" setting and create a call as the rule below.
C will hear busy tone when C call to D if there is one line in call waiting status for A. 3702A SIP Phone SIP GW IP 3702B D E Configuration Enable the Call Waiting function of the FXS port (D) of M3700 gateway. This function can be configured for each FXS port individually. Web Folder: Channel\ Connection Type A: FXS port of M3700 Series B, C: SIP Device (M3700 Series, other brand SIP gateway. SIP phone...
M3700 user manual 8.7 Target the Media (RTP) For the SIP call passing through NAT, it is possible that the media would not deliver properly; owing to the RTP contact information (IP address, port number) is different from original RTP packet. This function selects different contact information for M3700 to send RTP Packets to other SIP device within far-end NAT.
9. WEB MANAGEMENT INTERFACE The Tree Architecture of Web Management is shown below HOME BASIC GENERAL IP SETTING ADVANCED GENERAL SIP COMMON SIP OUTBOUND AUTHENTICATION SIP INBOUND ATHENTICATION STUN DIALING PLAN FILE TEMPLATE INBOUND TRANSIT (for gateway has FXO port.
M3700 user manual 9.1 BASIC / GENERAL Category Section Description Default Setting Information Region ID Display region ID.(Read only) 0 Software Display software version.(Read only) Version BootRom Display BootRom Version.(Read only) Version Hardware Display hardware Version.(Read only) Version Card Type Display card type. (Read only) Up-Time Display the use time since from system reboot.(Read only) MAC Display MAC address.
Time Time Configuration Source Select the time server to synchronize Registrar the time of this gateway ♦ Registrar: Get the time data from the Registrar Server. ♦ NTP Server: Get the time data from the NTP Server NTP Server Input the address if the system use NTP server as time synchronization source. The gateway will synchronize with the NTP Server once a day. If the NTP server inputted here is not available or fail to response, the gateway will retry it every 5 minutes.
M3700 user manual 9.2 IP SETTING Category Section Description Default Setting IP Settings IP State The way to obtain IP address: Manual Manual: Entered by user (Static IP) Auto(DHCP): Assigned by DHCP server PPPoE: Assigned by PPPoE of ISP Current Setting Display the configured IP 192.168.0.2 address, subnet mask address 255.255.255.0 and default gateway. (Read 192.168.0.1 only) 51 DCC NO.
Change To Enter the IP address that will be used after next restart, Including: IP Address Subnet Mask Address Default Gateway (This item is used only on Manual mode of IP Setting.) PPPoE Account Settings The user’s account of PPPoE protocol, provided by ISP. Password The user’s password of PPPoE protocol. Confirm Confirm the user’s password of Password PPPoE protocol. Service Name The service name of PPPoE account, provided by ISP.
M3700 user manual 9.3 ADVANCED / GENERAL Category Section Description Default Setting Flash Button Flash Time System confirmed 200 msec “Flash” time. Touch Tone (DTMF) Duration The duration to send a 100 msec DTMF. Inter-digit The inter-digit time of 100 msec sending string of DTMF digits. Guard Time Line The time defines how 0.8 sec long the system will not accept incoming call after previous call has been disconnected.
Time long to end the dialing 1-10 (seconds) number if a ‘#’ digit is missing. T.38 Fax Relay Redundancy Number of times to retry T.38 Fax protocol. Use more Redundant packet when network is unstable. No Redundant packet 1 Redundant packet 2 Redundant packets 3 Redundant packets 4 Redundant packets Voice Jitter Buffer Select the buffer time to Auto suppress voice delay vibration 1. Auto, the system detects it automatically. 2.
M3700 user manual 9.4 SIP COMMON Section Item Field Description Port and Header Port Default The control port number of SIP protocol. 5060 55 DCC NO.
Section Item Field Description Default Header Select ‘Standard’ or ‘Compact’ to be the Standard Form header format of SIP packet. When Compact is selected, the header will be shorter and it saves bandwidth. Outbound Proxy Domain Setting Name Registrar Setting Out-band DTMF Domain name or IP address of proxy. Empty Disable Port Control port number of SIP protocol. 5060 Domain Domain name or IP address of proxy Empty Name that you want to register.
M3700 Section Item Field Description G.723.1: user manual Default Mark the selection to Enable Enable G.723.1 Codec PCMU: Mark the selection to Enable Enable PCMU Codec (G.711 u Law) PCMA: Mark the selection to Enable Enable PCMA Codec (G.711 A Law) SIP Entity Control Codec You can select the codec priority for G729-G723-P Priority your requirement.
Section Item Field Description Default Public Address Address Empty Setting Enter SIP phone number of the port. The phone number general assigned by SIP service provider. Default Account information for registering SIP Account Proxy Username: It may the same as your SIP number Password: Password for Authentication Confirm Password: Reconfirm Password Contact Address Current Display current setting of Setting Setting Contact Address.
M3700 Section Item Field Description Entity user manual Default Show ‘+ ‘ means the SIP entity is for the Empty channel. 9.5 SIP OUTBOUND AUTHENTICATION Section Item Field Description SIP Outbound Maximum Maximum number of entries (Read Only) 50 Authentication Default allowed Entered Number of entries of (Read Only) 0 authentication entered. Entries List of entries List Entity: Which entity that you select. (Read Only) Empty Realm: Domain name or IP address.
Section Item Field Description Default Update Enter the information of outbound Empty Entry authentication Entity: Select an entity. Realm: Domain name or IP address. Username: Enter Username of authentication. Password: Enter password of authentication. Confirm Password: Enter password again for confirmation. Delete Delete the information of outbound Entry authentication Empty Entity: Select an entity. Realm: Domain name or IP address. 9.
M3700 Section Item Field Description Maximum Maximum number of user manual Default (Read Only) 20 entries allowed Entered Number of entries of (Read Only) 0 authentication entered. Entries List Display the entries (Read Only) Empty Entity: Which entity that you select. Username: Username of authentication. Update Entry Enter entries of authentication Empty Entity: Which entity that you select. Username: Username of authentication. Password: Password of authentication.
9.7 DIALING PLAN Section Item Field Description Default Dialing Method Control Dialing Plan: Use dialing plan rule Dialing Plan Transparent: All number dialed is passed to Proxy Server Transparent (with Digitmap): All number dialed is passed to Proxy Server with digit map control For the detail of this function, please refer to 8.
M3700 Section Item Field Description Entered Number of entries of (Read Only) 1 user manual Default authentication entered. List Display the entries (Read Only) x The default value “x“ means that all numbers that you dial will first go through SIP proxy. Dial In Rewriting Add Dialing Plan Enter numbers. Example: 050. Empty Delete Entry Enter numbers for delete. Empty Control Digits dialed from M3700 can be Disable Rule rewrite to different digits and sent to SIP Proxy.
9.8 FILE TEMPLATE File template is the text data of your customized configuration. You can keep it for backup purpose. Configure other M3700 with this text file can save time to re-configure it. For this purpose, copy all text in this page (does not include left title column), paste to Windows Notepad and save it as SIP33XX.MEM (for example, SIP3304.MEM.
M3700 user manual This content of this file can be modified, then upload the file to Gateway. If there is lots of data need to create or modify, use this way can save lots of time. For the procedure to use FTP client to connect this gateway, please refer to 11.
Codecs-Selection = "1111" # (G729:1000,G723:100,G711U:10,G711A:1) Codec-Priority = 0 #(0~23) (refer to webpage) Hotline-Control = 0 # (0/1, Disable/Enable) RTP-Base-Port = 10000 Time-Source = 1 # (0/1, Registrar/NTP Server) NTP-Server = "ntpserver.com" Time-Zone = 24 # (0~29) (refer to webpage) DayLight-Saving = 0 # (0/1, Off/On) [SIP-ENTITY] Entity-No = 1 Entity-Control = 1 # (0/1, Disable/Enable) CLIR = 0 # (0/1, Disable/Enable) Public-Address = "user@registrar.
M3700 user manual [SIP-INBOUND-INFO] Realm = "realm.com" [SIP-INBOUND-AUTH] # format: (entity username password), entity 0 for all 0 "username_for_all" "password" 1 "username_for_1" "password" [STUN] STUN-Server-Control = 0 # (0/1, Disable/Enable) NAT-WAN-IP = "223.223.223.223" STUN-Refresh-Time = 60 # unit: seconds [STUN-SERVER] # format: (ip_address port) 223.223.223.224 3478 [SIP-PHONE-BOOK] # format: (index user_part host_part port via_proxy) 8888 "user" "registrar.
Out-Proxy-Status = 1 # (0/1, Web Path: ADVANCED\SIP COMMON Disable/Enable) Out-Proxy-Port = 5060 Web Path: ADVANCED\SIP COMMON Registrar-Domain = "sip99.yip.
M3700 user manual For the sequence of selection, please refer to web page. Hotline-Control = 0 # (0/1, Disable/Enable) Web Path: PHONEBOOK RTP-Base-Port = 4000 Web Path: BASIC\GENERAL Time-Source = 1 # (0/1, Registrar/NTP Web Path: BASIC\GENERAL Server) NTP-Server = "ntpserver.com" Web Path: BASIC\GENERAL Time-Zone = 24 # (0~29) (refer to webpage) Web Path: BASIC\GENERAL For the sequence of selection, please refer to web page.
Default-Account-User = "username" Web Path: ADVANCED\SIP COMMON Default-Account-PASS = "password" Web Path: ADVANCED\SIP COMMON RFC-2833-DTMF = 1 # (0/1, Web Path: ADVANCED\SIP COMMON Never/Negotiate) Forward-Address = "user2@registrar.
M3700 Auto-Answer = 0 # (0/1/2, user manual Web Path: Channel Disable/Enable/Enable w/Pincode) Call-Waiting = 0 # (0/1, Disable/Enable) Web Path: Channel T38-Fax = 1 # (0/1, No/Yes) Web Path: Channel Voice-Input-Gain = 0 # (0~12, -6~6) Web Path: Channel Voice-Output-Gain = 0 # (0~12, -6~6) Web Path: Channel [SIP-OUTBOUND-AUTH] # format: (entity Configuration of SIP Outbound Authentication realm username password), entity 0 for all 1 "ABC" "Lester" "1234" Web Path: ADVANCED\SIP OUTBOUND AUTHEN
[SIP-INBOUND-AUTH] # format: (entity Configuration of SIP Inbound Authentication username password), entity 0 for all 1 "Lester" "1234" Web Path: ADVANCED\SIP INBOUND AUTHENTICATION 0 "Jack" "5678" Web Path: ADVANCED\SIP INBOUND AUTHENTICATION [STUN] Configuration of STUN STUN-Server-Control = 0 # (0/1, Web Path: ADVANCED\STUN Disable/Enable) NAT-WAN-IP = "0.0.0.
M3700 user manual Proxy(0/1, No/Yes) [TELEPHONY] Configuration of Telephony DIAL-END-TIME = 4 # (1~10) (refer to WEB Folder: ADVANCED\GENERAL webpage) T38-RELAY = 3 # (0~4) (refer to webpage) WEB Folder: ADVANCED\GENERAL 9.9 INBOUND TRANSIT Only FONEM3700 gateway with FXO port has this web page. 73 DCC NO.
Group Field Description Default Value Transit call Warning Time This gateway will send warning tone periodically to 60 check if the line is still alive. If calling side fail to press any key after hearing the warning tone, the line will be disconnected. Release Call by This gateway will check the RTP packet Checking RTP 0 periodically to verify if the line is still alive. If no RTP packet is found, the gateway will disconnect the call.
M3700 user manual 9.10 STUN Section Item Field Description Default STUN Server Control Enable or Disable STUN Server service. Disable NAT WAN IP Address Input this NAT WAN IP helps you to pass through NAT without using STUN server. The port number inside and outside NAT should be the same.
Section Item Field Description STUN Server Maximum Maximum number of Setting Default (Read Only) 5 entries allowed Entered Number of entries of (Read Only) 0 STUN server that have been entered. List Display all of servers that (Read Only) have been entered. Add Empty Add a stun server IP Address: Enter IP address or Domain Name Port: Enter port number of service. Delete Empty Delete a stun server IP Address: Enter IP address. Port: Enter port number of service.
M3700 user manual 9.11 CHANNEL Category Section Description Default Setting Information Channel Channel number: Channel Display port type. (Read only) Type Phone: FXS Interface, connect 1 to telephone set or Fax machine. Line: FXO Interface, connect to phone line. 77 DCC NO.
Enable Channel For FXS port: Control Bothway: Can make and accept IP call and PSTN call from this channel Disable Disable all functions of this port. For FXO port: IN_Only: Accept calls from PSTN only Bothway: Accept call from PSTN or call dial from FXS Disable: Disable all functions of this port. Current State Display the current state of this port. (Read only) Enable/ Disable. Do not Enable/Disable does not Disturb disturb function Silence Enable/Disable the function.
M3700 Battery This mechanism will reverse Reverse the polarity promptly that help user manual OFF some PBX to identify the start and end of each call ON: Enable the function OFF: Disable the function Auto Answer This unit auto answer the call Disable from FXO Disable: Disable Auto Answer Enable: Enable Auto Answer Enable w/ Pincode: Enable Auto Answer and Pincode verification. Forward to SIP: When incoming FXO calls is answer, it is forwarded to a SIP destination address.
9.12 PHONE BOOK Section Item Field Description Apply to Hotline Control Default Enable or Disable the hotline function to Disable M4600 SIP Line or other SIP device to make hotline call. SIP Phone Book Maximum Maximum number of entries (Read Only) 200 allowed Entered Number of entries of phone (Read Only) 0 books entered. Entries Display phone books List Index: Dialing number (Read Only) Empty Public Address: SIP account. Port: Port number. Via Proxy: Via proxy or not.
M3700 10. user manual Use Private IP (Behind NAT) Using a Private IP in a NAT Environment The unit is able to communicate with other units under a NAT environment using Private IP addresses on the LAN side of your IP Sharing device. However you must configure the IP Sharing device to treat the unit as a Virtual Server using UDP port 5060,2000. You will have to ask MIS personnel to enable the ports listed in the following table.
11. File Management 11.1 File Types The naming convention to the file type of FONEM4496 is listed in the following table: File Name SIP3302.CFG SIP3304.CFG SIP33XX.CFG SIP3302.RUN SIP3304.RUN File Type System configuration file Executing file SIP33XX.RUN SIP3302.WEB SIP3304.WEB SIP33xx.WEB SIP3302.MEM SIP3304.MEM SIP33xx.
M3700 user manual Software Update by FTP for File Type RUN and WEB 1. Execute FTP Client Software, e.g. CuteFTP Enter IP Address, User Name (default is FTP), Password (the password of FTP and Console is same, and the default is blank), and the Port Number to 21 2. Click button Connect to get connection between gateway and FTP Client. The files of the gateway will be displayed on the window if the connection is successful. 83 DCC NO.
3. Select the file with extension of .RUN and click button Upload and then Yes to overwrite. (Please notice that the file name must be same as the file name in the Gateway, e.g. SIP3304.RUN). 4. After the file is overwritten (you may check if the time of the file is updated), Gateway has to run Cold Start to store the configure file, then the updating is effective. 5. Select the file with extension of .
M3700 12. user manual Appendix 12.1 Appendix A: Phone-Set Command Pick up the handset and listen for the dialing tone. Dial “##0000 and listen for three consecutive tones before setting the following parameters. After input the parameters, please dial ‘# to end the configuration. Note: If Dialing Mode is configured to Transparent, (refer to section 8.1 Dialing Plan) then all digits you dial is passed to SIP Proxy and all Phone-Set Command is disabled.
15 Change WEB 6 digits Password 16 Change FTP 6 digits Password 17 Register or 0: De-Register; 1: Register De-register (quit) the SIP Entity registration 40 Listen for the IP (ending ”#” is not required) Address 41 Listen for the Subnet (ending ”#” is not required) Mask 42 Listen for the Default (ending ”#” is not required) Gateway 46 Listen for WEB, FTP, 1:FTP; 2:HTTP 3:Telnet Telnet Port 47 Listen for Current (ending ”#” is not required) Public Address 95 Region ID 2 digits 97
M3700 user manual 12.
12.3 Specifications Voice Interface Loop start, 2 wire FXS interface Feeding Voltage: 20V Feeding Current: 30 mA FXO interface Connectors Loop start, 2 wire RJ-11 Connectors (3702/3704) IDC Connectors (3708/3716) Voice compression G.711/G.723/G.729AB Silence suppression VAD, CNG Echo cancellation G.165/G.
M3700 user manual 12.
V 56 W 57 12.
