Installation manual
Table Of Contents
- Table of Contents
- 1 System Outline
- 2 Activation Key Installation
- 3 Installation
- 3.1 Before Installation
- 3.2 Installation of the PBX
- 3.2.1 Unpacking
- 3.2.2 Names and Locations
- 3.2.3 Opening/Closing the Front Cover
- 3.2.4 Attaching Fan Guards
- 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing)
- 3.2.6 Installation of 3- or 4-shelf System (Tower Type)
- 3.2.7 Installation of 4-shelf System (Side-by-side Type)
- 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620)
- 3.2.9 Installing/Replacing the Power Supply Unit
- 3.2.10 Frame Ground Connection
- 3.2.11 Installing/Removing the Optional Service Cards
- 3.2.12 Cable Handling
- 3.2.13 Types of Connectors
- 3.2.14 Attaching a Ferrite Core
- 3.2.15 Fastening Amphenol Connector
- 3.2.16 Surge Protector Installation
- 3.3 Information about the Main Processing Card
- 3.4 Information about the Virtual Cards
- 3.5 Information about the Optional Shelf Expansion Cards
- 3.6 Information about the Built-in Shelf Expansion Card
- 3.7 Information about the CO Line Cards
- 3.8 Information about the Extension Cards
- 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144)
- 3.8.2 DHLC8 Card (KX-TDA0170)
- 3.8.3 DLC8 Card (KX-TDA0171)
- 3.8.4 DLC16 Card (KX-TDA0172)
- 3.8.5 SLC8 Card (KX-TDA0173)
- 3.8.6 EXT-CID Card (KX-TDA0168)
- 3.8.7 CSLC16 Card (KX-TDA0177), ESLC16 Card (KX-TDA6174), EMSLC16 Card (KX-TDA6175), and ECSLC24 Card (KX-TDA6178)
- 3.8.8 IP-EXT16 Card (KX-TDA0470)
- 3.9 Information about the Other Cards
- 3.10 Connection of Extensions
- 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays
- 3.12 Connection of Peripherals
- 3.13 LAN Connection
- 3.14 Power Failure Connections
- 3.15 Starting the PBX
- 4 Guide for the Maintenance Console
- 5 Troubleshooting
- 6 Appendix
- Index
3.2.7 Installation of 4-shelf System (Side-by-side Type)
When vertical space is limited, it is possible to install shelves side-by-side. Installing the system using base
stands (supplied with an optional Mounting Kit) makes it easy to reinstall shelves in a different place.
Construction of 4-shelf System (Side-by-side Type)
Expansion Shelf 3
Expansion Shelf 2
Metal Bracket
Metal Bracket
Support Bracket
Base Stand
Expansion Shelf 1
Wall Bracket
(Right)
Wall Bracket
(Left)
Basic Shelf
Metal Bracket
Metal Bracket
Base Stand
Support Bracket
WARNING
Be careful not to drop any components. Dropping components may damage them or cause an
injury.
CAUTION
• Do not block the openings of the shelf. Allow space of at least 10 cm (4 in) at the sides of the shelf,
and 20 cm (8 in) above the top-mounted shelf.
• Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on the
back of the shelf will not be blocked.
• Make sure that the surface behind the shelf is not made of wood.
Note
• Make sure to remove the front cover from each shelf before installing the shelves (refer
to "3.2.3 Opening/Closing the Front Cover").
• Do not install any optional service cards or a PSU in the shelves before installation.
• Make sure to install the shelves where the Bus Cable (supplied with a BUS-M card or BUS-ME card)
can reach the shelves.
90 Installation Manual Document Version 2009-12
3.2.7 Installation of 4-shelf System (Side-by-side Type)