Installation manual
Table Of Contents
- Table of Contents
- 1 System Outline
- 2 Activation Key Installation
- 3 Installation
- 3.1 Before Installation
- 3.2 Installation of the PBX
- 3.2.1 Unpacking
- 3.2.2 Names and Locations
- 3.2.3 Opening/Closing the Front Cover
- 3.2.4 Attaching Fan Guards
- 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing)
- 3.2.6 Installation of 3- or 4-shelf System (Tower Type)
- 3.2.7 Installation of 4-shelf System (Side-by-side Type)
- 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620)
- 3.2.9 Installing/Replacing the Power Supply Unit
- 3.2.10 Frame Ground Connection
- 3.2.11 Installing/Removing the Optional Service Cards
- 3.2.12 Cable Handling
- 3.2.13 Types of Connectors
- 3.2.14 Attaching a Ferrite Core
- 3.2.15 Fastening Amphenol Connector
- 3.2.16 Surge Protector Installation
- 3.3 Information about the Main Processing Card
- 3.4 Information about the Virtual Cards
- 3.5 Information about the Optional Shelf Expansion Cards
- 3.6 Information about the Built-in Shelf Expansion Card
- 3.7 Information about the CO Line Cards
- 3.8 Information about the Extension Cards
- 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144)
- 3.8.2 DHLC8 Card (KX-TDA0170)
- 3.8.3 DLC8 Card (KX-TDA0171)
- 3.8.4 DLC16 Card (KX-TDA0172)
- 3.8.5 SLC8 Card (KX-TDA0173)
- 3.8.6 EXT-CID Card (KX-TDA0168)
- 3.8.7 CSLC16 Card (KX-TDA0177), ESLC16 Card (KX-TDA6174), EMSLC16 Card (KX-TDA6175), and ECSLC24 Card (KX-TDA6178)
- 3.8.8 IP-EXT16 Card (KX-TDA0470)
- 3.9 Information about the Other Cards
- 3.10 Connection of Extensions
- 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays
- 3.12 Connection of Peripherals
- 3.13 LAN Connection
- 3.14 Power Failure Connections
- 3.15 Starting the PBX
- 4 Guide for the Maintenance Console
- 5 Troubleshooting
- 6 Appendix
- Index
PROBLEM PROBABLE CAUSE SOLUTION
• During a power failure,
extensions connected
to ports 1 to 4 of
EMSLC16/ESLC16/
ECSLC24/CSLC16 and
ports 1 to 2 of DHLC8/
SLC8 cards do not
operate.
• A DPT or APT is
connected to the
extension port.
• The dialing mode (tone
or pulse) is incorrect.
• Disconnect the DPT or APT and connect
an SLT.
• Set the Tone/Pulse switch to the other
position.
• Originating an outside
call, call transfer, or
conference cannot be
performed.
• The corresponding
flexible button does not
exist on the PT.
• Program the flexible button. Refer to
"6.1.3 Flexible Buttons" in the Feature
Manual.
• The KX-HGT100 does
not work properly, or
some features cannot
be performed using the
KX-HGT100.
• The firmware of the
KX-HGT100 and the
MPR software file
version of the PBX are
not upgraded to their
latest versions.
• Upgrade the firmware of the KX-HGT100
and the MPR software file version of the
PBX to their latest versions.
Document Version 2009-12 Installation Manual 217
5.1.3 Operation