Installation manual
Table Of Contents
- Table of Contents
- 1 System Outline
- 2 Activation Key Installation
- 3 Installation
- 3.1 Before Installation
- 3.2 Installation of the PBX
- 3.2.1 Unpacking
- 3.2.2 Names and Locations
- 3.2.3 Opening/Closing the Front Cover
- 3.2.4 Attaching Fan Guards
- 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing)
- 3.2.6 Installation of 3- or 4-shelf System (Tower Type)
- 3.2.7 Installation of 4-shelf System (Side-by-side Type)
- 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620)
- 3.2.9 Installing/Replacing the Power Supply Unit
- 3.2.10 Frame Ground Connection
- 3.2.11 Installing/Removing the Optional Service Cards
- 3.2.12 Cable Handling
- 3.2.13 Types of Connectors
- 3.2.14 Attaching a Ferrite Core
- 3.2.15 Fastening Amphenol Connector
- 3.2.16 Surge Protector Installation
- 3.3 Information about the Main Processing Card
- 3.4 Information about the Virtual Cards
- 3.5 Information about the Optional Shelf Expansion Cards
- 3.6 Information about the Built-in Shelf Expansion Card
- 3.7 Information about the CO Line Cards
- 3.8 Information about the Extension Cards
- 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144)
- 3.8.2 DHLC8 Card (KX-TDA0170)
- 3.8.3 DLC8 Card (KX-TDA0171)
- 3.8.4 DLC16 Card (KX-TDA0172)
- 3.8.5 SLC8 Card (KX-TDA0173)
- 3.8.6 EXT-CID Card (KX-TDA0168)
- 3.8.7 CSLC16 Card (KX-TDA0177), ESLC16 Card (KX-TDA6174), EMSLC16 Card (KX-TDA6175), and ECSLC24 Card (KX-TDA6178)
- 3.8.8 IP-EXT16 Card (KX-TDA0470)
- 3.9 Information about the Other Cards
- 3.10 Connection of Extensions
- 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays
- 3.12 Connection of Peripherals
- 3.13 LAN Connection
- 3.14 Power Failure Connections
- 3.15 Starting the PBX
- 4 Guide for the Maintenance Console
- 5 Troubleshooting
- 6 Appendix
- Index
5.1 Troubleshooting
5.1.1 Installation
PROBLEM PROBABLE CAUSE SOLUTION
You cannot make/receive
calls via an IP network.
• IP-EXT/IP-GW/DSP
card malfunction
• Replace the corresponding card.
• IPCEMPR card
malfunction
• Replace the IPCEMPR card (be sure to
turn off the PBX when replacing).
• Not enough activation
keys
• Purchase additional activation key codes.
Please consult a certified dealer for
details.
• Poor connection • Make sure that an 8-pin twisted pair cable
is used for connection.
• Make sure that none of the CAT 5 cables
in use are over 100 m (328 ft) in length.
• Make sure that a straight cable is used for
connection to a switching hub.
• Network malfunction • Make sure that all network devices in use
are switched on.
• Make sure that there is no unwanted
firewall in the IP network.
IP-PTs/SIP Extensions do
not operate.
• IP-EXT/DSP card
malfunction
• Replace the corresponding card.
• IPCEMPR card
malfunction
• Replace the IPCEMPR card (be sure to
turn off the PBX when replacing).
• Not enough activation
keys
• Purchase additional activation key codes.
Please consult a certified dealer for
details.
• IP-PT/SIP Extension
not registered
• Register the corresponding IP-PT/SIP
Extension.
• IP-PT/SIP Extension
malfunction
• Replace the IP-PT/SIP Extension.
• Poor connection • Make sure that an 8-pin twisted pair cable
is used for connection.
• Make sure that none of the CAT 5 cables
in use are over 100 m (328 ft) in length.
• Make sure that a straight cable is used for
connection to a switching hub.
• Network malfunction • Make sure that all network devices in use
are switched on.
• Make sure that the IP-PT/SIP Extension
is not blocked by the firewall or other
network devices.
210 Installation Manual Document Version 2009-12
5.1.1 Installation