Installation manual
Table Of Contents
- Table of Contents
- 1 System Outline
- 2 Activation Key Installation
- 3 Installation
- 3.1 Before Installation
- 3.2 Installation of the PBX
- 3.2.1 Unpacking
- 3.2.2 Names and Locations
- 3.2.3 Opening/Closing the Front Cover
- 3.2.4 Attaching Fan Guards
- 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing)
- 3.2.6 Installation of 3- or 4-shelf System (Tower Type)
- 3.2.7 Installation of 4-shelf System (Side-by-side Type)
- 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620)
- 3.2.9 Installing/Replacing the Power Supply Unit
- 3.2.10 Frame Ground Connection
- 3.2.11 Installing/Removing the Optional Service Cards
- 3.2.12 Cable Handling
- 3.2.13 Types of Connectors
- 3.2.14 Attaching a Ferrite Core
- 3.2.15 Fastening Amphenol Connector
- 3.2.16 Surge Protector Installation
- 3.3 Information about the Main Processing Card
- 3.4 Information about the Virtual Cards
- 3.5 Information about the Optional Shelf Expansion Cards
- 3.6 Information about the Built-in Shelf Expansion Card
- 3.7 Information about the CO Line Cards
- 3.8 Information about the Extension Cards
- 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144)
- 3.8.2 DHLC8 Card (KX-TDA0170)
- 3.8.3 DLC8 Card (KX-TDA0171)
- 3.8.4 DLC16 Card (KX-TDA0172)
- 3.8.5 SLC8 Card (KX-TDA0173)
- 3.8.6 EXT-CID Card (KX-TDA0168)
- 3.8.7 CSLC16 Card (KX-TDA0177), ESLC16 Card (KX-TDA6174), EMSLC16 Card (KX-TDA6175), and ECSLC24 Card (KX-TDA6178)
- 3.8.8 IP-EXT16 Card (KX-TDA0470)
- 3.9 Information about the Other Cards
- 3.10 Connection of Extensions
- 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays
- 3.12 Connection of Peripherals
- 3.13 LAN Connection
- 3.14 Power Failure Connections
- 3.15 Starting the PBX
- 4 Guide for the Maintenance Console
- 5 Troubleshooting
- 6 Appendix
- Index
3.9.5 ESVM4 Card (KX-TDA0194)
Function
4-channel simplified voice message card for Built-in Simplified Voice Message feature. Also supports MSG
card features. To be mounted on the OPB3 card.
Screw
ESVM Card
OPB3 Card
inside
Accessories and User-supplied Items
Accessories (included): Screws ´ 3
User-supplied (not included): none
CAUTION
When installing/uninstalling an ESVM card, be careful not to damage the chips around the connection
parts. Doing so may cause severe damage to the ESVM card.
Notice
• When replacing an ESVM card, ensure that the status of the OPB3 card is In Service (INS), and then
initialize the ESVM card. For details about the initialization procedure, refer to "2.5.4 Tool—Simplified
Voice Message—Delete All Recording" in the PC Programming Manual.
• When installing an ESVM card for the first time on an OPB3 card that is already installed in the PBX,
do not remove the OPB3 card from the PBX until the card status becomes INS.
• After installing the OPB3 card, with an ESVM card mounted, for the first time, do not remove the
OPB3 card from the PBX until the card status becomes INS.
Note
When using an ESVM card for the SVM feature, it must be mounted on sub-slot 3 (highest slot) of the
OPB3 card.
Document Version 2009-12 Installation Manual 175
3.9.5 ESVM4 Card (KX-TDA0194)