PLAY-ZONE METAL SWING SET MODEL# 9335MSS PRODUCT MANUAL - VERSION 6.21.01 FOR AGES: 3-6 WEIGHT LIMIT: TO BUILD: Lbs 75Lbs per seat X 300 TOOLS NEEDED 2 Quick Set Concrete Manual en español ubicado en GQBrands.com Spanish Manual located at GQBrands.com CUSTOMER SERVICE GQBrands.com • CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: Please Note: In the interest of better quality and value, we are constantly improving and updating our product information. Most up to date manuals, warnings and product information can be found at: https://www.globalqualitybrands.com/warnings PLAY-ZONE METAL SWING SET MODEL# 9335MSS To register you product please visit: www.globalqualitybrands.com/product-registration or Scan code If you have an issue with your item, do not return.
WARNINGS IMPORTANT MESSAGE Please read all of the warnings and directions below prior to assembly. This product comes equipped with warnings and instructions for the assembly, care, maintenance and use of the product. This information must be read by all product supervisors and users before any person is allowed to use this product. ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age.
WARNING LABEL LOCATIONS CAUTION 300 LBS 75lbs per seat MODEL# 9335MSS MADE IN CHINA Global Quality Brands - PureFun.net 4401 Samuell Blvd, Ste 150 Mesquite, TX 75149 CustomerService@GQBrands.com Global Quality Brands - PureFun.net 4401 Samuell Blvd, Ste 150 Mesquite, TX 75149 CustomerService@GQBrands.com The labels shown on this page have been attached to the METAL SWING SET in the indicated location Note: The labels are not shown actual size. 4 GQBrands.com CustomerService@GQBrands.
WARNINGS & SAFETY INFORMATION Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • This unit must be assembled and disassembled by ADULTS ONLY. • Keep a copy of your assembly instructions for future reference. This can be particularly helpful for identification of parts. • This Swing Set is suitable for use by most children 3 to 6 years of age.
PARTS LIST YC40 - Swing Seat YC51 - Stem Cover YBB4 - Upper Leg Pole x4 B211 - Lower Leg Pole x4 x2 x2 YD2 - Leg Bracket YC52 - Foot Rest x4 x2 x2 YB22 - Seat Beam YD3 - Swing Hook YB19 - Upper Seesaw Pole x2 YC50 - Seesaw Seat x4 x2 YB20 - Lower Seesaw Pole YB1 - Top Beam Male YD1 - Bracket x2 x1 YBB5 - Cross Beam x2 x2 YB2 - Top Beam Fem ale x1 YN1 x4 8x50/M6 x2 YE1 6x35 YD10 6 6 YN2 x10 8x45/M6 x2 YE5 8x78 x8 YD11 8 YN3 x4 8x40/M6 YE12 x8 6x40 x26 YD12
ASSEMBLY INSTRUCTIONS STEP 1-4 YBB4 x4 YD11 x14 YL1 x14 YD1 x2 YB1 x1 YB2 x1 YN1 x4 YN2 x10 YG13 x14 Step 1: Assemble the frame by connecting the 2 Top Beams, part YB2 (Top Beam Female) and YB1 (Top Beam Male) together. Make sure to check the holes are facing the right direction and that the open ends of the swing bracket on beam YB2 is facing downward. Step 2: Secure using the YN2, YL1, D11 and YG13 nuts and bolts and tighten with provided allen key as shown in diagram.
ASSEMBLY INSTRUCTIONS STEP 5-7 YL2 YB211 YBB5 x4 x4 x2 YG13 x4 YE12 x4 YD10 x4 YC40 x2 YD3 x4 YG2 x4 Step 5: Attach the B211 (Lower Leg Pole) into B210 Upper Leg Pole. Repeat on all 4 legs. Step 6: Locate part B5 (Cross Beam) and attach the green end caps. Next attach the B5 Cross Beam to the B211 Upper Leg Poles using E12, L2, D10 and G13 nuts and bolts. Secure with allen key and repeat on other side. Step 7: Locate Part C40 (Swing) Connect the D3 (Swing Hook) through the swing bracket.
ASSEMBLY INSTRUCTIONS STEP 8-10 YD11 x4 YG2 x4 YF2 x2 YD12 x2 YC3 x8 YG13 x4 YL1 x4 YB19 x2 YB20 x2 YB22 x2 YN4 x4 YE5 x2 Step 8: Assembling the Seesaw Attach part C3 nylon washers into the holes of the top of B19 (Upper Seesaw Pole) and place the D12 metal washer onto one side. Slide the B19 upper pole into the bracket and attach with the F2 bolt and washer and G2 parts as shown. Tighten the G2 nut until the inner spacing is about 1.25 inches apart. Repeat for other pole.
ASSEMBLY INSTRUCTIONS STEP 11-12 YD11 YL1 YF11 YC50 YG13 YC51 YC52 YG1 YE1 10 GQBrands.com Step 11: Place the C50 (Seesaw Seat) on top of the beams and x8 secure with Parts F11, D11, L1 x8 and G13 like diagram shown. Each seat has 4 sets and x2 need to be tightened with allen key x8 x8 Step 12: Slide the C51 (Green Stem x2 Cover) and C52 (Foot Rest) over the B20 Beam. Secure x2 with Nut, washer and bolt parts x2 G1 and E1.
ASSEMBLY INSTRUCTIONS STEP 13-15 YL2 x4 YD10 x4 YE12 x4 YD2 x4 YG13 x4 Step 13: We recommend setting this playground set in concrete for safety and security purposes. Locate and mark the position for the legs. Check the dimensions shown on diagram on page 9. Dig square holes of 14x14x14 inches deep and wide and fill with quick set concrete. (Not Included) The top of the concrete should not exceed ground level. Step 14: While concrete is wet.
ASSEMBLY INSTRUCTIONS Dimensions Warning: Maximum fall height is 71" (180 cm) 12 GQBrands.com CustomerService@GQBrands.
FREQUENTLY ASKED QUESTIONS Question: “How should I clean my swings and seesaw?” Question: “A seat seems loose, what should I do?” Answer: you should clean the product with a solution of warm water and Non- Corrosive/Abrasive soap. Dampen a rag with this solution and wipe completely dry before using. Answer: Make sure the Bolts/Nuts under the plastic seat are secure. Question: “Something was missing from the packaging,” “I need to purchase a replacement part” or “I discovered a damaged piece.
