DURA-BOUNCE 15FT TRAMPOLINE ENCLOSURE MODEL# 9315TS - ENCLOSURE PRODUCT MANUAL - VERSION 05.17.01 FOR AGES: WEIGHT LIMIT: TO BUILD: 6+ N/A X TOOLS NEEDED: 2 CUSTOMER SERVICE GQBrands.com CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: DURA-BOUNCE 15FT TRAMPOLINE ENCLOSURE MODEL# 9315TS - ENCLOSURE To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at At GQBrands®, we want all of our customers to be completely satisfied with their purchase. Take time to review the contents of the product you have just received to make sure that all of the parts are included.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • Ensure the trampoline has been assembled correctly, per the instructions in the manual. • It is essential that the intended site for this trampoline is completely flat and level.
PARTS LIST 1- Straight Enclosure Pole x6 2- Curved Enclosure Pole x6 3- Enclosure Pole Cap 9- Enclosure x6 4- Screw x12 x1 5- Thick Curved Plastic Washer x12 6- Washer x12 7- Nut x12 8- Black Nut Cap x12 4 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 1: Gather all Curved Enclosure Poles (Part 2) and Enclosure Pole Caps (Part 3). IMPORTANT: Do not attach the Enclosure Pole Caps to the Straight Enclosure Poles. Once an Enclosure Pole Cap has been installed it cannot be removed. Snap and click all Enclosure Pole caps to the Curved Enclosure Pole. The button must be pushed down, and you will hear a click once successfully attached.
ASSEMBLY INSTRUCTIONS STEP 3: A. Remove the Nut and Screw from 15FT Enclosure Trampoline on the right side of the U-Shaped Leg. Do not remove all nuts and bolts at the same time, only 1 set a time to keep the strength of the Frame at all times. NOTE: Make sure to keep removed parts stored or in a safe place away from the mat while building the Enclosure. B. With the help of another adult, hold the completed enclosure pole by aligning both square holes to begin installation.
ASSEMBLY INSTRUCTIONS 4 Screw MODEL# 9315TS - ENCLOSURE 5 6 Spacer Washer 7 8 Nut Black Nut Cap 4 5 6 7 8 4 5 6 7 8 7
ASSEMBLY INSTRUCTIONS STEP 4: Place the Enclosure Net (Part 9) on top of the trampoline. Align the straps to the corresponding Enclosure Poles so they are as near to each other as possible when lifted NOTE: Make sure that zipper and buckle snap are facing the outside of the trampoline. This is good to ensure that Enclosure is not reversed.
ASSEMBLY INSTRUCTIONS STEP 6: A B C D E MODEL# 9315TS - ENCLOSURE A. To attach the enclosure netv to the Pole Caps, grab the corresponding strap at the top of the Enclosure Net and slip through the opening of the Pole cap. B. Detach the snaps by pushing on the middle of the buckle. C. Connect Male Buckle Snap (Fork Side) to the strap. D. Once Male Buckle snap is fastened, Re-attach to the other side of the buckle. E. You will successfully connect both sides when you hear them click.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.com 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149 10 GQBrands.com CustomerService@GQBrands.
