DURA-BOUNCE 8FT TRAMPOLINE SET MODEL# 9308TS PRODUCT MANUAL - VERSION 09.17.02 FOR AGES: 6+ WEIGHT LIMIT: 250 Lbs 113 Kgs TO BUILD: X TOOLS NEEDED: 1 CUSTOMER SERVICE GQBrands.com CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: DURA-BOUNCE 8FT TRAMPOLINE SET MODEL# 9308TS - TRAMPOLINE To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at At GQBrands®, we want all of our customers to be completely satisfied with their purchase. Take time to review the contents of the product you have just received to make sure that all of the parts are included.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • It is essential that the intended site for this trampoline is completely flat and level. If the ground is not level this will cause movement in the frame and could cause stress on the joined sections.
TRAMPOLINE - PARTS LIST 1- Trampoline Mat 2- Frame Pad x1 3- Curved Frame with T-Section x1 4- “U” Shaped Leg x6 5- Leg Extension 6- Spring x6 4 x3 7- Screw x48 8- Spring Tool x6 GQBrands.com CustomerService@GQBrands.
ENCLOSURE - PARTS LIST 10- Upper Pole with Cap 9- Lower Pole x6 11- Pole Cover x6 x12 13- M8 Bolt 12- Enclosure Net x12 14- M8 Nut x12 x1 15- Plastic Washer x12 16- Washer x12 MODEL# 9308TS 5
ASSEMBLY INSTRUCTIONS STEP 1: 3 Parts: Part 3 (x6) - Curved Frame with T-Section Lay out the Curved Frames (3) in the ground as shown in the picture with the spring openings facing the floor. 3 3 Slide all six Curved Frames onto each other to complete a full circled frame. 3 3 STEP 2: Parts: Part 5 (x6) - Extension Leg Part 4 (x3) - “U” Shaped Leg Attach the Leg Extensions (3) to all TSection with the horizontal opening facing the inside of the frame.
ASSEMBLY INSTRUCTIONS STEP 4: Once all x3 “U” Shaped Legs have been installed, allign the T-Sections from the Frame and slide until all have 3 assembled legs are secure. STEP 5: Parts: Part 1 (x1) - Trampoline Mat Place the Trampoline Mat (1) in the middle of the frame, with the logo facing upwards and the stitching facing the floor.
ASSEMBLY INSTRUCTIONS LEARNING TO INSTALL SPRINGS (6) “R” Hook “C” Hook Install the Spring (6) by placing the “R” Hook on the V-Ring of the Trampoline Mat. Using the Spring Tool (8), pull the “C” Hook until it reaches the opening in the frame.
ASSEMBLY INSTRUCTIONS STEP 7: Parts: Part 2 (x1) - Frame Pad 2 Unfold the Frame Pad (2) and place it on top of the Top Rail and springs. The Frame Pad must cover the Top Rails completely to avoid injury. STEP 8: Tighten the Elastic Straps at the bottom of the Frame to the top rail to secure to the trampoline.
ASSEMBLY INSTRUCTIONS STEP 9: Parts: Part 9 (x6) - Lower Pole Align the opening Lowe Poles (9) to the horizontal opening of the T-Section and the middle opening of the Leg extension. 9 STEP 10: Following the instructions on Page 11, install all Lower Poles to all t-Section from the Top Rail Lower Pole Locations 10 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS 13 14 M8 Bolt M8 Nut MODEL# 9308TS 16 15 Plastic Washer Washer 13 14 15 16 13 14 15 16 11
ASSEMBLY INSTRUCTIONS STEP 11: Parts: Part 11 (x6) - Pole Cover Slide x6 Pole Covers (11) once all Lower Poles have been installed. 11 11 11 11 11 11 STEP 12: 11 10 Parts: Part 10 (x6) - Upper Pole with Cap Part 11 (x6) - Pole Cover Slide x6 Pole Covers (11) to an Upper Pole with Cap (10) to have x6 completed pieces NOTE: If the Upper Pole is missing a Cap or became detached, simply install back into the Pole to make sure the Cover doesn’t slide out. x6 12 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 13: 12 Parts: Part 12 (x1) - Enclosure Net Slide all x6 completed upper poles into the enclosure pole covers in the Enclosure Netting. NOTE: Leaving the zipper open will make it easier to install the enclosure netting.
ASSEMBLY INSTRUCTIONS STEP 14: Insert each Upper Pole and slide down to the Lower Pole attached to the trampoline, one at a time to distribute the tension of the enclosure netting evenly. Once placed, slide the net and the covers until they complete cover the lower poles, 4 3 2 5 6 14 1 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 15: Close the zipper of the enclosure netting and secure with all x3 Click and Snap Hooks. Make sure that the Enclosure Netting is stretched to the outside of the Trampoline Frame Pad. STEP 16: At the bottom of the Enclosure netting there are hooks that need to be attached to the V-Rings of the trampoline. Secure all Hooks to tighten the Enclosure netting to the trampoline as shown.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.com 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149 16 GQBrands.com CustomerService@GQBrands.
