DURA-BOUNCE 8FT TRAMPOLINE SET MODEL# 9308TS PRODUCT MANUAL - VERSION 08.18.06 FOR AGES: 3-9 WEIGHT LIMIT: 250 Lbs 113 Kgs TO BUILD: X TOOLS NEEDED: 2 CUSTOMER SERVICE GQBrands.com CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: DURA-BOUNCE 8FT TRAMPOLINE SET MODEL# 9308TS - TRAMPOLINE To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at At GQBrands®, we want all of our customers to be completely satisfied with their purchase. Take time to review the contents of the product you have just received to make sure that all of the parts are included.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • It is essential that the intended site for this trampoline is completely flat and level. If the ground is not level this will cause movement in the frame and could cause stress on the joined sections.
TRAMPOLINE - PARTS LIST 1- Trampoline Mat 2- Frame Pad x1 3- Curved Frame with T-Section x1 4- “U” Shaped Leg x3 x6 5- Leg Extension 6- Spring 7- Screw x6 x6 x48 TOOLS INCLUDED 8- Spring Tool 20- Wrench x1 4 21- Screwdriver x1 GQBrands.com x1 CustomerService@GQBrands.
ENCLOSURE - PARTS LIST 10- Upper Pole 9- Lower Pole x6 11- Pole Foam x6 12- Pole Sleeve x12 x6 13- Pole Cap 14- Enclosure Net x6 15- 80mm M8 Bolt x12 x1 16- M8 Nut x12 17- Plastic Washer x12 18- Washer x12 22- Cap Nut x12 9308TS 5
ASSEMBLY INSTRUCTIONS STEP 1: Parts: Part 4 (x3) - “U” Shaped Leg Part 5 (x6) - Extension Leg 4 Attach the Leg Extensions (3) to all TSection with the horizontal opening facing the inside of the frame. 5 Place the “U” Shaped Legs (5) with the openings aligning to the horizontal opening from the Extension Leg. 5 STEP 2: Parts: Part 7 (x6) -Screw With the openings aligned, use a screwdriver to unite the Leg Extensions and the “U” Shaped Leg. 7 x3 6 GQBrands.
Frame a legs are ASSEMBLY INSTRUCTIONS Make su Shaped trampo Leg Ext STEP 4: Once all x3 completed Legs have been installed, Flip each at a time and connect them to ensure they stay connected. With the help of another adult, carefully flip the complete frame so it stands on its own.
ASSEMBLY INSTRUCTIONS LEARNING TO INSTALL SPRINGS (6) “R” Hook “C” Hook Install the Spring (6) by placing the “R” Hook on the V-Ring of the Trampoline Mat. Using the Spring Tool (8), pull the “C” Hook until it reaches the opening in the frame.
ASSEMBLY INSTRUCTIONS STEP 7: Parts: Part 2 (x1) - Frame Pad 2 Unfold the Frame Pad (2) and place it on top of the Top Rail and springs. The Frame Pad must cover the Top Rails completely to avoid injury. STEP 8: Tighten the Elastic Hook at the bottom of the Frame to the V-Ring as shown to secure to the trampoline.
ASSEMBLY INSTRUCTIONS STEP 9: Parts: Part 9 (x6) - Lower Pole Align the openings of the Lower Pole (9) to the openings of the T-Section and the middle opening of the Leg extension. 9 STEP 10: Following the instructions on Page 11, install all Lower Poles to the frame of the trampoline. Lower Pole Locations 10 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS 15 16 80mm M8 Bolt 9308TS M8 Nut 17 Plastic Washer 18 22 Washer Nut Cap 15 13 17 14 18 15 16 16 22 15 13 17 14 18 15 16 16 22 11
ASSEMBLY INSTRUCTIONS STEP 11: Parts: Part 11 (x6) - Pole Foam 11 11 Slide x6 Pole Foams (11) once all Lower Poles have been installed. 11 11 11 11 STEP 12: Larger opening x6 Parts: Part 10 (x6) - Upper Pole Part 11 (x6) - Pole Foam Part 12 (x6) - Pole Sleeve Slide all x6 Pole Foams to x6 Upper Poles. Once assembled, locate the larger opening of the Pole Sleeve and slide till the top of the upper pole shows on the smaller opening of the sleeve. x6 x6 Smaller opening 12 GQBrands.
ASSEMBLY INSTRUCTIONS STEP 13: Slide all x6 Assembled Upper Poles with the larger opening sliding through the bottom pole. Make sure that the top of the Bottom Pole aligns and attached to the bottom Upper pole when sliding the sleeve down. STEP 14: Parts: Part 13 (x6) - Pole Caps Place all x6 Pole caps at the top of the Upper Poles.
ASSEMBLY INSTRUCTIONS STEP 15: Parts: Part 14 (x1) -Enclosure Net Place the Enclosure Net (Part 14) in the middle of the Trampoline, and hook each upper loop to a Pole Cap NOTE: Leaving the zipper open will make it easier to install the enclosure netting. 14 14 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 16: Close the zipper of the enclosure netting and secure with the Buckle Hook. At the bottom of the Enclosure netting there are hooks that need to be attached to the V-Rings of the trampoline. Secure all Hooks to tighten the Enclosure netting to the trampoline as shown.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.com 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149 16 GQBrands.com CustomerService@GQBrands.
