LADYBUG JUMPER KIDS TRAMPOLINE MODEL# 9022LB PRODUCT MANUAL - VERSION 04.16.01 FOR AGES: 4-10 WEIGHT LIMIT: 150 Lbs 68 Kgs ADULT(S) NEEDED: TOOLS NEEDED: WARNING/ADVERTENCIA • Do not allow more than one person on this product at any time. • Children must be supervised by an adult at all times. • Not recommended for children under 3 years of age. • The contents of this package are not suitable for children under 3 years of age. Contains small parts which may cause choking. • ADULT ASSEMBLY REQUIRED.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: LADYBUG JUMPER KIDS TRAMPOLINE MODEL# 9022LB At Global Quality Brands®, we want all of our customers to be completely satisfied with their purchase. Please take time to review the contents of the product you have just received to make sure that all of the parts are included. If you find that any parts are missing or damaged, we will happily provide replacement parts at no charge within 30 days of purchase.
LIMITED WARRANTY Global Quality Brands® warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of 90 DAYS FROM THE DATE OF ORIGINAL PURCHASE. This Limited Warranty is not transferable and is available only for the original purchaser of the Product. The Company’s obligation under this warranty is limited to replacing or repairing the Product, at the discretion of the company.
WARNINGS IMPORTANT MESSAGE WARNING - PLEASE READ ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. WARNING: While every attempt is made to ensure the highest degree of protection in all equipment, we cannot guarantee freedom from injury. The user assumes all risks of injury due to use. All merchandise is sold on this condition, which no representative of the company can waive or change. 4 GQBrands.com CustomerService@GQBrands.
WARNINGS Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • This unit is designed only for jogging in place and similar bounding exercises. • Not recommended for children under 3 years of age. • Maximum weight limit: 150 lbs. (68 kgs) • Children MUST NEVER use the trampoline unless supervised by a responsible adult with knowledge of trampoline use.
ASSEMBLY WARNINGS • Make sure the trampoline is placed on a stable and leveled surface. • The recommended overhead clearance is a minimum of 10 feet from any and all ceilings, overhead cables, ceiling fixtures or hard surfaces.
PARTS LIST 1A 8A 9 Front 8B 1B 1C 1D Back 10 11 12 14 Medium 2 13 3 15 Small Large 16 Front 4 5 40mm 50mm 6 Back 7 MODEL# 9022LB 7
ASSEMBLY INSTRUCTIONS STEP 1: Assembled Frame The Frame (Part 1A), Jumping Mat (Part 1B), Springs (Part 1C), & W-Hooks (Part 1D) will come assembled in one piece. Place assembled Frame on an even, clean, & flat surface to install. Make sure that there are no obstructions in your way when building this Trampoline. NOTE: Make sure that the spring ends are facing up, and the logo printed on the Jumping Mat is facing the floor. Opening Locations A A A A B Identify all openings on the Frame Pad.
ASSEMBLY INSTRUCTIONS STEP 2: Locate x8 T-Section Pieces (Part 2), x4 40mm Square Neck Bolts (Part 4), & x4 Screw Nuts (Part 6). Locate the (A) openings in the frame (Shown in page 8) to begin installing the T-Sections Pieces into the Frame. A. Place a T-Section Piece on the outside of the frame and the other half from the inside of the Frame. (2) All openings will line up. Make sure that the T-Sections are facing up to install the legs in Step 4. (2) B.
ASSEMBLY INSTRUCTIONS STEP 3: Locate x4 Cross-Section Pieces (Part 3), x4 40mm Square Neck Bolts (Part 4), and x4 Screw Nuts (Part 6). A Locate the (B) openings in the frame (Shown in page 8) to begin installing the Cross-Sections Pieces into the Frame. (3) A. Place a Cross-Section Piece on the outside of the frame and the other half from the inside of the Frame. All openings will line up. (3) B. Insert x2 40mm Square Neck Bolts (Part 4) from the outside of the frame to show the smooth surface.
ASSEMBLY INSTRUCTIONS STEP 4: Locate x6 Leg Poles (Part 8A), x6 Leg Caps (Part 8B), x6 40mm Square Neck Bolts (Part 4), and x6 Screw Nuts (Part 6). (8A) NOTE: The Leg Poles and Caps might come preassembled, to facilitate assembly, separate them. Place the Leg Caps aside. (8B) x6 Assembled Legs STEP 5: Place all Leg Poles (Part 8A) inside the inserts. Align openings from the T-Sections & Cross-Sections to the Legs. STEP 6: A.
ASSEMBLY INSTRUCTIONS STEP 7: A A. Insert x1 50mm Square Neck Bolt (Part 5) into the upper part of the CrossSection and secure with a x1 Screw Nut. (5) (6) B. Tighten loosely with the wrench provided. Repeat this step on the second Cross Section Pieces NOTE: All Screws in the Cross-Sections will be tightened in Step 15 B Tighten Loosely 12 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 8: A (7) A. Flip the Assembled Frame. Make sure to align the two openings in the Frame Pad (Part 7) assigned for the upper Cross-Section Pieces. Place on top to cover the Frame & Jumping Mat letting the upper part of the Cross-Section Pieces to show. B. The Frame Pad is able to stretch to cover the Springs and W-Hooks. Stretch the Frame Pad to make sure it is snug and properly covering the whole trampoline frame. C.
ASSEMBLY INSTRUCTIONS STEP 9: A A Flip the Assembled Frame. Locate the 3 Loop rings in the “A” sections located in the skirt of the Frame Pad and locate the 4 Strings located in the “B” Sections A A. Grab a loop hole corresponding to the Leg Pole and hook them. Make sure the skirt is properly hiding the legs B B Once the loop is hooked to the Leg Pole, insert the Leg Cap (Part 8B). Repeat these steps to all “A” Sections. B.
ASSEMBLY INSTRUCTIONS STEP 10: A Flip the Frame with Frame Pad properly attached A. Grab the Plush Face (Part 16) and flip it upside down and align it to the Leg Pole between both Cross-Sections. B. On the back of the Plush face there is a sleeve opening. Align it with the corresponding Leg Pole and insert it. C. Grab the Leg Cap (Part 8B) and place it into the Leg Pole (Part 8A) to make sure the Plush Face is secure.
ASSEMBLY INSTRUCTIONS STEP 11: Align the Velcro fasteners from the edges of the Frame Pad skirt, to the Velcro strips from the Plush Face (Part 16). Press tightly together and secure the Plush Face to the Frame Pad of the trampoline. Flip The Trampoline whole and set aside until handle bar is completed 16 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS A STEP 12: B A. Attach x1 Straight Pole (Part 9) by pressing the snap button at the bottom of x1 Left Corner Pole (Part 10) Insert and push until the button finds a desired opening. (10) B. Select between the two heights options in the Straight Pole for the safest height. C. Slide x1 Small Foam Tube (Part 13) and slide x1 Medium Foam Tube (Part 14) D. Make sure that both foams are pressed against each other to avoid the poles to show.
ASSEMBLY INSTRUCTIONS STEP 14: Slide Large Foam Tube )Part 15) into the Handler Bar (Part 12) until it stays in the middle of the bar. (12) Press the snap Button on each side of the Handle Bar and slide until both have found the top openings of the Corner Poles. (15) Make sure that both foams are pressed against each other to avoid the poles or buttons to show. NOTE: Failure to properly cover the poles can result in pinching or injury to the user. 18 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 15: A A. Once the completed Handle Bar is assembled, slide both ends of the Straight Poles into the openings of the Cross-Section Pieces. B. Insert x1 50mm Square Neck Bolt (Part 5) with the smooth service from the inside of the trampoline. C. Secure with x1 Screw Nut (Part 6) from the outside. Repeat these steps to secure both sides of the handle bar into the trampoline.
FREQUENTLY ASKED QUESTIONS • Question: “The Handle Bar is not aligned to the Straight Poles, I am unable to Snap & Click since they are not in position” Answer: Loosen up the upper sections of the Cross-Section Pieces so you may be able to twist the Poles. The bottom opening is wider, which helps position the upper two openings properly. Once you do this, you should be able to insert the Handle Bar.
