Western Electric Fireplace Insert Model Number: (EF42D, EF43D, EF44D, EF45D, EF302A) OWNER’S MANUAL WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.
CONTENT 1. Important Safety Information …………………………………..………........... 1 2. Technical Specifications ………………………….…………………………………... 4 1) Electric Specifications ....……………………………….………….............. 4 2) Product Specifications ………..……....……………………….….............. 4 3. Before Installation …………..…………………………….………….................... 5 1) Check …………..……………………………………………………………………..… 5 Spare Parts Checking ………..……………………....……………………….... 5 Kindly Suggestion ……………….....………………………….…………........ 6 4.
1. IMPORTANT SAFETY INFORMATION WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
use with an extension cord or relocatable power tap (outlet/power strip). Connect to properly grounded outlets ONLY. DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater. NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp, or come in contact with water.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet. ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If this heater trips the circuit breaker, unplug all other appliances on the same circuit before the next use. Avoid plugging other appliances into the same circuit as this heater. NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections.
2. TECHNICAL SPECIFICATIONS 1) Electric Specifications Model Volt Watt Hz BTU(max) Amp (min/max) Heating Area(max) EF42-45D, EF302A 120 750/1500 400 square feet 60 4600 12.5 2) Product Dimensions Units: inches Model EF42D EF43D EF44D EF45D EF302A 4 A 24.80 27.95 31.89 35.04 35.04 B 22.91 25.96 29.90 33.05 33.05 C 21.89 25.20 29.02 32.29 32.29 D 16.93 20.02 23.95 27.10 27.10 E 21.46 24.61 24.61 26.99 22.44 customerservice@puraflame.com F 20.04 23.19 23.19 25.55 21 G 8.78 8.78 8.78 8.
3. BEFORE INSTALLATION 1) Check: WARNING! DO NOT use this Electric Fireplace if any part has been under water. Immediately call a qualified service technician to inspect and to replace any part of the electrical system if necessary. Keep plastic wrapping away from children. Spare Parts Checking Open the packaging carefully and remove the polystyrene. Check all the spare parts are fully received. Carefully check if any damages that may have for the spare parts.
Below parts are packed in one bag Owner’s Manual ×1 pc Remote Handset ×1 pc Battery ×1 pc 2) Kindly suggestions Keep the packaging (carton, rapping bag, repacking bag, etc.) for future transportation and/or storage. If there is any problem or question, please contact the service team. If the unit needs to be returned, please make sure all the spare parts are packed inside, and packing as per the repacking instruction, tie it with the provided straps at last. Note: This model cannot be hard wired.
1) Locating the Appliance Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location, ensure that the general instructions for safety are followed. For best results, install out of direct sunlight, water or very damp air. Power supply service must be installed within proximity of electric fireplace prior to finishing avoiding reconstruction.
SKU EF42D EF43D EF44D EF45D EF302A Width 21.9-23.9 25.2-27.2 29.1-31.1 32.3-34.3 32.3-34.3 Opening sizes ranges/inches Height Depth (min) 20.1-21.3 23.2-24.4 23.2-24.4 7.8 25.6-26.6 21-22 Depth (suggest) 8.1 Prepare the opening and outlet, place the unit into the framed opening gently and no fixing brackets are needed. Note: If the existing opening is found a little bit narrow, the handles on both sides could be removed. 8 customerservice@puraflame.
4) Insert into a cabinet or wood mantel. It is available to install the unit into a wood cabinet or mantel. Also, it would be better to keep the depth at 8.1”. The clearance from the top of the unit to the bottom of TV or something else sitting on the cabinet should be 8” at least. When moving the insert into a mantel, DO NOT let bottom of insert touch the mantel to avoid scratches. 5.
5a. Manual Control Panel Note: When the heater is first turned on, a slight odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time. BUTTON NAME POWER SWITCH 10 FUNCTION Turn the main power switch on. A long “beep” sound will be heard when the switch is turned at ON Position “I”. Note: The remote control will lost the memory for function settings when the switch is turned at OFF Position “O”. customerservice@puraflame.
FLAME HEATER 6 3 5 7 2 4 8 THERMOSTAT The flame will be cycled from Flame A – Flame B – Flame C – Flame Off. Flame A: full bright flame + little blue Flame B: full bright flame Flame C: half bright flame The heater will be cycled from Low – High – Heater Off. The indicator light on left to Power Switch (see the right picture on last page) will illuminate when the heater is turned on. The indicator light will go out within 10s. Low: (●○) High: (●●) Note: 1. Heater can be used without flame. 2.
5b. Remote Control Note: Remote control can be used only when the main power switch is on. Aim the remote control at the remote receiver (see picture on page10) which is on the left of the main power switch. BUTTON 12 TITLE FUNCTION POWER The power button will put the unit in standby mode. This will turn off all functions and hold the settings in memory, press the power button again will turn on the unit to previous settings. For the first time use, Flame A will be turned on.
FLAME The flame will be cycled from Flame A – Flame B – Flame C – Flame Off. LOW HEAT To turn on the heater on half heat setting or turn off the heater. HIGH HEAT To turn on the heater on full heat setting or turn off the heater. To turn on the crackling and cycle through high crackling sound – normal crackling sound – low CRACKLING cracking sound - high crackling with wind sound – normal crackling with wind sound – low crackling with wind sound- off.
If it switches off again, UNPLUG THE HEATER RIGHT AWAY! Have the outlets, wiring, and breaker box inspected by a professional. Make necessary repairs before using the heater. 6. CARE AND MAINTENANCE ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. Cleaning NEVER immerse in water or spray with water.
Electrical and Moving Parts: The fan motors are lubricated at the factory and will not require lubrication. Electrical components are integrated in the fireplace and are not serviceable by the consumer. Storage: Store heater in a clean dry place when not in use. Replacement parts: Use only replacement parts supplied by the manufacturer. Use of any other parts, or modifying the fireplace in any way, will void all warranties. No internal parts are replaceable or serviceable. 7.
8. TROUBLESHOOTING GUIDE 1. The remote does not work and the new unit we just got cannot be turned on. 1) Make sure the main power switch on the top right behind the fence is on. 2) There would be a long beep when the main power switch is turned on. 3) If there is no beep, the connecters on the PCB board might be loosen, please contact service team for a checking instruction.
motor is not in right position. b. If not, please contact service team for help. 5. The heater does not come back even the room is already cold. Turn the thermostat to 9 to see if the heater will work continuously, if yes, the sensor is malfunction, if not, please contact service team for help. 6. The flame does not show up or flicker or a noise when turn it on. Please contact service team for a checking instruction of the flame LED board connecter, flame motor and spindle. 7.
Ningbo Richen Electrical Appliance Co., Ltd Address: No.19, Yongdinghe Road, Xiapu, Beilun, Ningbo PR. China www.puraflame.com 3.EF.43.05.
