BALI Bali ShowerSpa Model #1050 Owner's Manual
Bali Model #1050 Please Read The Following Instructions COMPLETELY Before Beginning! Our goal is to ensure your installation goes smoothly and safely. Please read these instructions carefully and follow recommendations for plumbing and mounting. After reading instructions, if you determine you do not have the necessary skills and/or tools, we recommend that a licensed plumbing contractor complete the installation. If you encounter any problems during installation PLEASE VISIT CUSTOMER SUPPORT AT WWW.
Product Dimensions 5.5 in. 139.7 mm 9.5 in. 241.3 mm Finished Wall Line 34.5 in. - 876.3 mm 48 in. - 1219.2 mm 34 in. - 863.6 mm Measured To Bottom Of Bracket 11 in. - 279.4 mm 9.75 in. 247.65 mm 8 in. 203.2 mm 19 in. - 482.6 mm 9 in. 228.6 mm 53 in. - 1346.2 mm 9 in. 228.6 mm 30.25 in. - 768.35 mm 23.5 in. - 596.9 mm Measured To Bottom Of Bracket 6 in. 152.
Bali Parts Legend 2 3 1 19 18 4 16 6 15 5 10 17 14 13 12 9 7 1. ShowerSpa 2. Escutcheon 3. Shower Arm 4. Rubber Screen Washer 5. Shower Head 6. Stainless Nut 7. Hose Washer.........................2 8. Hand Shower Hose 9. Hand Shower 10. Set Screw...............................3 11. Hand Shower Holder 12. Allen Bolt 13. Lock Washer 14. Allen Wrench (2mm) 15. Coarse Thread Screw..........4 16. ShowerSpa Wall Bracket...2 17. Nylon Wall Anchor...............4 18. Nylon Nut 19.
Assembly After unpacking your ShowerSpa, some assembly is required prior to installation. Shower Arm Assembly 1. On the back of the ShowerSpa near the top, unscrew the hose fitting from the safety insert (19) and retain rubber washer. Remove the safety insert and discard with plastic nut (18). 2. Place escutcheon (2) over threaded end of shower arm (3) and insert through opening. Use stainless nut (6) to secure shower arm to ShowerSpa. Then secure both set screws (10) located on the stainless nut. 3.
Installation – New Construction Extensive Remodel – New Finished Wall Surface 1. Prior to sheetrock, stub-out ½" hot and cold supply lines beyond finished wall surface, 4" on center. For best results, attach 90° brass fittings (available at most hardware stores) to the stub-outs maintaining ¼" – ½" of space between the fitting and finished wall. The open end of the 90° brass fittings should point down so the supply lines attach parallel to the wall. 1 2.
Installation – New Construction Extensive Remodel – New Finished Wall Surface 1. Prior to sheetrock, stub-out ½" hot and cold supply lines beyond finished wall surface, 4" on center. For best results, attach 90° brass fittings (available at most hardware stores) to the stub-outs maintaining ¼" – ½" of space between the fitting and finished wall. The open end of the 90° brass fittings should point down so the supply lines attach parallel to the wall. 1 2.
MANUFACTURER'S LIFETIME LIMITED WARRANTY 1. Defects Covered; Warranty Period: Pulse Shower Spas, Inc. (“Pulse”) warrants to the original consumer purchaser who purchases this shower spa (the “Product”) for use in his or her own home, that the Product will be free from defects in material and manufacturing workmanship for as long as the original consumer purchaser owns that same home.
