Owners manual
22
7
Figure A
3
4
2
1
21
7
18
19
20
17
5
6
7
8
8
10
6
11
12
13
23
15
16
15 16
No.
No.No.
No. Descriptio n
Descriptio nDescriptio n
Descriptio n Qty.
Qty.Qty.
Qty.
1.
1.1.
1. Aloha Showerspa 1
2.
2.2.
2. Showerarm 1
3.
3.3.
3. Rubber washer 6mm 1
4.
4.4.
4. Shower head 1
5.
5.5.
5. Top cover 1
6.
6.6.
6. Brass nut 2
7.
7.7.
7. Rubber washer 2mm 3
8.
8.8.
8. 90 degree fitting 2
9.
9.9.
9. Compression nut 2
10.
10.10.
10. Rubber washer with screen 1
11.
11.11.
11. Retaining washer 1
12.
12.12.
12. Mounting plate 1
13.
13.13.
13. ½ X 2½ inch brass nipple 1
14.
14.14.
14. Two faced tape 1
15.
15.15.
15. Mushroom head wall anchor 6
16.
16.16.
16. 1in. (25.5 mm) Nail insert 6
17.
17.17.
17. Handshower mount 1
18.
18.18.
18. Nut 4mm 2
19.
19.19.
19. Non slip washer 2
20.
20.20.
20. 1
⅜
(36mm) machine
screw
2
21.
21.21.
21. Handshower 1
22
2222
22 Handshower hose 59 in. (1.5M) 1
9
9
A
B
C
900mm
54.2mm
995mm
100mm
14
If you encounter any problems during installation
call customer service toll free at 888-785-7320
before returning item to store.
Please read these instructions carefully to become familiar with the components [See Figure A],
installation procedures and tools required. Follow the steps in the order presented to help avoid any
mistakes
.
Tools required: Cordless Drill, 3/16in.(5mm) tile/masonry bit, hammer, adj. wrench, Philips screwdriver
and pencil.
1. Insert mounting plate (12) into slots on back of Aloha (1). Hold Aloha (1) to wall and evaluate
preferred mounting location based on height of shower arm, shower head, body spray height based
on existing shower arm outlet. Determine which hole in mounting plate (12) will be used (A-top, B-
middle or C-bottom) for preferred height. The convenient “cut to fit” supply line (23) allows these
three options.
2. Remove shower head and any escutcheon (cover) from existing shower arm.
3. Determine length of ½ inch NPT nipple required:
a. Place mark on existing shower arm at the wall surface.
b. Unscrew shower arm from elbow in wall.
c. Measure distance from mark made on shower arm to end of shower arm threads.
d.
Add ½ inch to this measurement, then round up to nearest ½ inch. (I.e. measurement = 1 ¾ in. +
½ inch = 2¼ in. rounded up to nearest ½ in increment = 2½ inch NPT nipple. Note: If supplied
2½ in. nipple (13) is not correct length you must obtain the correct size - sold separately. NPT
brass nipples are readily available at most hardware stores.
4. Apply generous amount of Teflon tape and/or pipe sealant to nipple (13) and adequately tighten into
elbow in wall ensuring no leaks. Important: Do not damage or mar the final ½ inch of nipple threads
protruding from wall.
5. Insert shower arm (2) into body of Aloha Showerspa (1) and secure with nut (6). Insert washer (7)
into 90 degree fitting (8) on shower arm supply line and securely tighten 90 degree fitting (8) to
shower arm ensuring no leaks. Caution: do not over-tighten.
6. Attach handshower mount (17) to side of Aloha (1) with machine screw and non slip washer and nut.
7. If using hole A for mounting continue to Step 10. If using hole B or C of mounting plate (12)
remove mounting plate from Splash. Loosen compression nut (9) and remove 90 degree fitting (8).
Cut the supply line (23) at the predetermined mark depending on hole choice. Important: Supply
line must be cut clean and square to ensure no leaks - take your time, maybe even practice higher
up on hose!
8. Slide compression nut (9) onto supply line (23).
9. Push supply line (23) over barbed portion of 90 degree fitting (8) until it bottoms against base of
threads.
10. Slide compression nut (9) onto to 90 degree fitting (8) and securely tighten
11. Remove face of tape (14) from mounting plate (12) and slide plate over nipple (13) through
predetermined hole A, B or C. Level plate before adhering to wall.
12. Push retaining washer (11) over nipple (13) securing mounting plate (12) to wall and/or use nut (6)
13. Optional: secure mounting plate using supplied wall fasteners. Drill 5mm (3/16in.) wide X 25mm
(1in.) deep holes using a masonry/tile drill bit. CAUTION: live (active) plumbing is behind the
wall! Insert mushroom head anchors (15) through plate and carefully hammer nail (16) flush to
mushroom head anchor.
14. Insert washer with screen (10) into 90° fitting (8) and connect to nipple (13). Turn on water and
check for leaks. Once leak free carefully slide Aloha (1) onto mounting plate (12) and push down to
secure.
15. Insert 6mm washer (3) into showerhead (4) and attach to Aloha (1).
16. Insert washer (7) into each end of shower hose (22) and secure hex head to Aloha (1) and cone
shape end to handshower (21).
Usage:
Use the diverter valve to select what function you want to enjoy. If you want two functions to operate at
the same time, position the diverter selector between the two desired functions.
It is best to wipe dry the Aloha Showerspa after each use to maintain it in new looking condition. Only
use mild soap and water to clean the Aloha Showerspa. Never use any abrasives or harsh chemicals as
they will damage the finish and void the warranty.