ELECTRIC QUAD OWNER’S MANUAL FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ • ATV QUAD DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? CALL (866)-434-6067 05. 19.
Table of Contents Safety and Warnings Before You Start Assembly Hardware Maintenance Before You Ride Repair and Maintenance Troubleshooting Motorbike Components Warranty 2-3 4 5-6 7 7 8-12 13 14 15 Safety and Warnings WARNING: Riding an electric quad can be a dangerous activity. Certain conditions may cause components to fail without fault of the manufacturer.
Safety and Warnings To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools, or other bodies of water. Maintain a hold with both hands on the handlebars at all times. Never allow more than one person at a time to ride the quad. , steering system, wheels and all other moving components. Never ride while using a cell phone or wearing headphones.
Before You Start WARNING: Remove all packing and items from the display box. Make sure that the power switch is turned “OFF” before assembling the quad. NOTE: the ATV Quad is to be assembled by an adult. Estimated Assembly Time • Allow up to 15 minutes for assembly, not including initial charge time. • Allow up to 14 hours for the initial charge (see page 6 for charging information).
Assembly Handlebar Assembly Tools required: 5mm hex wrench, 10mm wrench C A D E F B 1. Align handlebars vertically and horizontally onto clamps (A&B). Install the 4 clamp bolts (C) and lock nuts (D) and hand tighten. 2. Tighten bolts evenly and securely with a 5mm hex wrench (E) and 10mm wrench (F). 3. Check to ensure handlebars are tight by applying pressure before riding, handlebars should not move backwards or forwards.
Assembly Charging the Battery WARNING: Battery must be fully charged before you ride your electric quad. Required components: battery charger • Initial battery charge time - 14 hours • Recharges after initial charge - up to 10 hours • When quad is not in regular use batteries need to be charged on a monthly basis to maximize performance A 1. Make sure power switch is in the OFF position before plugging in the charger. Insert charger into charging port (A) on the right side of the battery box. 2.
Hardware Maintenance Brake Check the brakes for proper function. When you squeeze the lever, the brake should provide positive braking action. When you apply the brake with the throttle engaged, the brake cut off switch should stop the motor. Make sure that the brakes are not rubbing when the lever is not being applied. Frame, Fork and Handlebars Check for cracks or broken connections.
Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Adjusting the Brakes Tools required: 10mm wrench Loosen Tighten 1. To adjust the brake cable, turn the adjuster barrel on the brake lever clockwise (loosen) or counter clockwise (tighten). Only turn the barrel in small increments until the desired adjustment is reached. If brake continues to need further adjustment proceed to the next step. 2.
Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Replacing the Chain Tools required: 5mm hex wrench, 6mm hex wrench, 10mm wrench, Philips head screwdriver 1. Remove the rear right side axle bolt hardware with a 6mm hex wrench. 2. Remove the thru axle bolt on the inside of the wheel with a 5mm hex wrench and 10mm wrench. 4. Locate and remove the master link clip (A) and slide out the master link from the chain. Remove the entire chain. 5.
Repair and Maintenance WARNING: RISK OF FIRE. Do not bypass the blade fuse. Replace only with manufacturer replacement parts. Battery Care and Disposal Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C). THIS MOTORBIKE CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE LAWS.
Repair and Maintenance Battery Charger Only use the supplied battery charger. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance Products™ electric quad recommended battery charger. Only use the battery(ies) specified by the manufacturer. Wheels Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for excess wear and adjust and replace drive train components as required.
Troubleshooting Problem Possible Cause Solution Quad will not run. Battery is not charged. Fully charge the battery. First charge should be 14 hours and up to 10 hours for recharges. Wires or connectors are loose or unplugged. Check to ensure that charger is tightly plugged into both the wall and the quad. Battery requires charging. Fully charge the battery. First charge should be 14 hours and up to 10 hours for recharges. Quad run time is short.
Electric Quad Components part description part description part description 1 Throttle assembly 16 Chain 31 Controller 2 Handlebar 17 Gear 32 Guide wheel 3 Handlebar clamp 18 Gear drive mount 33 Tensioner mount 4 Brake lever 19 Chain guard cover (inner) 34 Motor 5 Left grip 20 Battery lock 35 Left side cover 6 Seat 21 Batteries 36 Left foot rest 7 Body 22 Right fender bracket 37 Front wheel 8 Deck cap 23 Frame 38 Front wheel hub mount 9 On/Off switch
Warranty Pulse Performance Products™ Limited Warranty The manufacturer warranties this product to be free of manufacturing defects for a period of 90 days from the date of purchase. This Limited Warranty does not cover normal wear and tear, tires, cables, or any damage, failure or loss caused by improper assembly, maintenance, storage or use of this Pulse Performance Products™ electric quad. This warranty is limited to the replacement of defective parts only.
Pulse Performance Products™ A Division of Bravo Sports™ 12801 Carmenita Rd.
