User Instructions

ManualsBrandsPulsar ManualsOpen frame / Enclosed / DesktopPS 12V/10A enclosed switch mode power supply unit

PS-15012100

PS 12V/10A enclosed switch mode power supply

Edition: 10 from 01.03.2018

Supersedes the edition: 9 from 27.05.2014

Features:

 power output 10A/12÷15V DC

 wide range of AC input voltage 176÷264V

 high efficiency 83%

 LED indication

 protections:

 short-circuit protection SCP

 over voltage protection OVP

 surge protection

 overload protection OLP

 warranty – 2 year from the production date

1. Technical description.

1.1. General description.

The power supply unit is intended for 230V AC mains supply to alarm system devices, which require 12V DC voltage

and current efficiency of I=10A. The design enables simple changing of the output voltage, within the range of 12V÷15V DC,

using a potentiometer. The power supply unit is protected against a short circuit, an overload, a surge or over voltage.

1.2. Specifications.

Supply voltage

176 ÷ 264V AC; 50÷60Hz

Current consumption

1,1A@230V AC max.

PSU power

150W max.

Efficiency

83%

Output current t

AMB

<30°C

10A - see chart 1.

Output current t

AMB

=40°C

7A - see chart 1.

Voltage adjustment range

12V ÷ 15V DC

Ripple voltage

100mV p-p max.

Short-circuit protection SCP

electronic (activation requires disconnecting the load or supply for

about 5 s.)

Overload protection OLP

105 ÷ 150% of the PSU power (activation requires disconnecting the

load or supply for about 5 s.)

Surge protection

varistors

Over voltage protection OVP

>16V (activation requires disconnecting the load or supply for about

20 s.)

LED indication

green LED – presence of DC voltage

Operation conditions

2-nd environmental class, temperature: -10

C ÷ +40

relative humidity 20%...90%, without condensation

Dimensions

L=199, W=110, H=50 [+/- 2mm]

Net/gross weight

0,73kg / 0,78kg

Protection class PN-EN 60950-1:2007

I (first) – requires a protective conductor (PE)

Connectors

power-supply:Φ0,63-2,50 (AWG 22-10)

outputs: Φ0,63-2,50 (AWG 22-10)

Dielectric strength of insulation:

- between input (network) circuit and output

circuits of the PSU (I/PO/P)

- between input circuit and PE protection circuit

(I/P-FG)

- between output circuit and PE protection circuit

(O/P-FG)

3000 V/AC min.

1500 V/AC min.

500 V/AC min.

Insulation resistance:

- between input circuit and output or protection

circuit

100 MΩ, 500V DC

Storage temperature

-20ºC...+60ºC

Vibrations and impulse waves during transport

PN-83/T-42106

* In order to extend the life of the power supply, the load current of 7A is recommended.

See graph 1.

Summary of content (4 pages)

PAGE 1
PS-15012100 PS 12V/10A enclosed switch mode power supply Edition: 10 from 01.03.2018 Supersedes the edition: 9 from 27.05.2014 EN PL Features:     *  power output 10A/12÷15V DC wide range of AC input voltage 176÷264V high efficiency 83% LED indication  protections:  short-circuit protection SCP  over voltage protection OVP  surge protection  overload protection OLP warranty – 2 year from the production date 1. Technical description. 1.1. General description.
PAGE 2
1.3. Temperature characteristics. Chart 1. Acceptable output current from the PSU depending on ambient temperature (instantaneous load). 2. Installation. 2.1. Requirements. The PSU is to be mounted by a qualified installer, holding relevant permits and licenses (applicable and required for a given country) for 230V AC and low-voltage installations. The unit should be mounted in confined spaces, according to the environment class II, of normal air humidity (RH=90% max.
PAGE 3
2.4. Dimensions and fitting of the PS-15012100 power supply. Fig. 2. Mechanical view of the PSU. 3. Maintenance. Any and all maintenance operations may be performed following the disconnection of the PSU from the power supply network.
PAGE 4
WEEE MARKING According to the EU WEE Directive – It is required not to dispose of electric or electronic waste as unsorted municipal waste and to collect such WEEE separately. Pulsar sp. j. Siedlec 150, 32-744 Łapczyca, Poland Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50 e-mail: biuro@pulsar.pl, sales@pulsar.pl http:// www.pulsar.pl, www.zasilacze.