POE084824B v.1.0 PoE 54V/8x0,3A/4x7Ah PoE buffer power supply for up to 8 IP camera. EN* Edition: 4 from 25.05.2015 Supersedes the edition: 3 from 15.05.
www.pulsar.
www.pulsar.pl GREEN POWER CCTV PoE POE084824B 1. Technical description. 1.1. General description. The PSU is designed for supply of up to 8 webcams requiring stabilized voltage of 48V DC(+/-15%). The PSU supplies voltage of 54V DC and total current capacity of I=8x0,3A+0,2A Battery charging*. In case of mains power loss, the unit will instantly switch to battery operation. There are 8 power supply outputs, independently protected by melting fuses or PTC polymer fuses.
www.pulsar.pl GREEN POWER CCTV PoE POE084824B [11] Optional, external optical indication connector (factory setting) [12] PE – grounding the shield of the RJ45 connectors (factory setting) Table 1. The description of components of the PoE module. Fig. 2. Components arrangement. Fig. 3. The view of the PSU. Component No. [Fig.
www.pulsar.pl GREEN POWER CCTV PoE POE084824B [6] TAMPER – microswitch (contacts) of antisabotage protection (NC) [7] Plate for mounting the network switch (Ethernet switch / hub) Tab. 2. Components of the PSU (see Fig. 3). 1.4 Technical parameters. - electrical parameters (Table 3) - mechanical parameters (Table 4) - safety of use (Table 5) - operation parameters (Table 6) Electrical parameters (Table 3).
www.pulsar.pl GREEN POWER CCTV PoE POE084824B Safety of use (Table 5). Protection class PN-EN 60950-1:2007 Protection grade PN-EN 60529: 2002 (U) Insulation electrical strength: - between input (network) circuit and the output circuits of the PSU (I/P-O/P) - between input circuit and PE protection circuit (I/P-FG) - between output circuit and PE protection circuit (O/P-FG) Insulation resistance: - between input circuit and output or protection circuit Operation parameters (Table 6).
www.pulsar.pl POE084824B GREEN POWER CCTV PoE 2.2. Installation procedure. 1. Before installation, cut off the voltage in the 230V power-supply circuit. 2. Mount the PSU in a selected location and lead the connecting cables. 3. If required, mount the switch network (Ethernet Switch / Hub) on the mounting plate (element 6, Figure 3) using cable ties supplied with the PSU. An example of mounting the Ethernet switch is shown in Figure 4: Figure 4. An example of mounting the Ethernet switch. 4.
www.pulsar.pl POE084824B GREEN POWER CCTV PoE - battery output (0V): BAT- cable / black 10. Check the optical indication of the PSU status: green LED light on the PoE module. 11. Close the cover after installing and checking the operation of the power supply. 3. Power supply operation indication. 3.1. Optical indication.
www.pulsar.pl POE084824B GREEN POWER CCTV PoE CAUTION! The arrangement of contacts at the figure 7 shows a potential-free status of the relay, which is equivalent to a state with no voltage at any of the AUX1 ÷ AUX8 outputs. TAMPER – output indicating enclosure opening: - volt free contact input indicating the status of the power supply doors, PSU closed: contacts closed (NC), PSU open: contacts open (NO). 4. Service and operation. 4.1. Overload or short-circuit of the power supply output.
www.pulsar.pl POE084824B GREEN POWER CCTV PoE WEEE LABEL Waste electrical and electronic equipment must not be disposed of with normal household waste. According to the European Union WEEE Directive, waste electrical and electronic equipment should be disposed of separately from normal household waste. CAUTION! The power supply unit is adapted for cooperation with the sealed lead-acid batteries (SLA). After the operation period they must not be thrown but recycled according to the applicable law.
