HPSBOC 7012C v.1.1 HPSBOC 13,8V/6A/17Ah/OC Buffer switch mode power supply unit with technical outputs. EN Edition: 9 from 01.03.2018 Supercedes edition: 8 from 01.06.
www.pulsar.
www.pulsar.pl GREEN POWER plus HPSBOC7012C 6. Buffer power supply unit HPSBOC 13,8V/(5V÷7,4V)/2A/17Ah. - HPSBOC7012C + DCDC20 (5V÷7,4V/2A) + 17Ah BATTERY 7Ah: 1. Buffer power supply unit HPSBOC 13,8V/12x0,5A/7Ah. - HPSBOC7012C + LB4 4x0,5A (AWZ574 or AWZ576) + LB8 8x0,5A (AWZ578 or AWZ580) + 7Ah 2. Buffer power supply unit HPSBOC 13,8V/12V/5x1A/7Ah. - HPSBOC7012C + RN500 (13,8V/12V) + LB8 5x1A (AWZ580 or AWZ579) + 7Ah 3. Buffer power supply unit HPSBOC 13,8V/(2x5V÷7,4V/2x2A)/7Ah.
www.pulsar.pl HPSBOC7012C Fig. 2. The view of the PSU. Description of PSU components and connectors (tab.2, fig.3). Element no. Description [Fig. 3] [1] PSU module [2] TAMPER, contact, sabotage protection (NC) Tab.2. Output terminals of the PSU. Fig.3. The view of the PSU.
www.pulsar.pl GREEN POWER plus HPSBOC7012C 1.4 Specifications: - electrical parameters (tab.3) - mechanical parameters (tab.4) - operation safety (tab.5) - operating parameters (tab.6) Electrical parameters (tab. 3) Mains supply Current up to Supply power Efficiency Output voltage 176÷264V AC 0.95A@230VAC 100W max.
www.pulsar.pl GREEN POWER plus HPSBOC7012C Mechanical parameters (tab.
www.pulsar.pl HPSBOC7012C GREEN POWER plus As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical system shall follow valid standards and regulations. 2.2 Installation procedure. 1.
www.pulsar.pl HPSBOC7012C GREEN POWER plus 3.2 Technical outputs The PSU has indication outputs: EPS - absence of AC supply output: - OC type output that indicates AC power loss. Under normal status, with 230V AC supply, the output is connected to ground (L level – 0V). In case of power loss, the PSU will switch the output into high impedance state hi-Z after approx. 10s. - relay output indicating the absence of AC supply.
www.pulsar.pl HPSBOC7012C GREEN POWER plus 4. Operation and use. 4.1 Overload or short circuit of the PSU output (SCP on) In case of overload, the output voltage is automatically shut off, and so is the LED indicator. The restoration of the voltage takes place immediately after the failure (overload) is over. 4.2 Battery-assisted operation. In case of a main power outage, the device is immediately switched into a battery-assisted operation.
www.pulsar.pl GREEN POWER plus HPSBOC7012C WEEE MARK According to the EU WEE Directive – It is required not to dispose of electric or electronic waste as unsorted municipal waste and to collect such WEEE separately. The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled according to the applicable law. Pulsar sp. j. Siedlec 150, 32-744 Łapczyca, Poland Tel. (+48) 14-610-19-40, Fax.
