Manual




6.7 I
n

U
s
t
p
o
c
o









6.7.1
P


6.7.1.1

T
a
n
p
u
t
h


6.7.1.2

T
bl
s
e
t
h

6.7.1.3

T
t
h
c
o

B
c
o
S

F
s
w
a
n


6.7.2
U


The follo
w
necessar
y
n
itial Po
w
U
pon initial p
o
t
ar
t
-up scree
n
o
sition. Onc
e
o
nfigurabilit
y
P
ol
y
feede
r
Local Mod
e
T
he first ope
r
n
d adjuste
d
u
sh button
a
h
e syste
m
in
Remote St
a
h
e second co
n
l
ending syste
m
e
tpoin
t
is set
l
h
is mode of o
p
Remote St
a
T
he third co
n
h
is mode, th
e
o
ntact input
.
B
y providing
o
nt
r
ol the p
o
CADA/PL
C
or safety p
u
w
itch. All
n
d setup pa
r
U
ser Inte
r
w
ing table, u
s
y
key press se
q
w
er Up
a
o
we
r
applicat
i
n
sequence.
T
e
the start-up
y
via the prog
r
Figure
6
r
B and B
e
r
ational mo
d
fro
m
the “L
o
a
nd placing
t
this mode.
a
rt/Stop M
o
n
trolle
r
oper
a
m
from a re
m
l
ocally and u
s
p
eration.
a
rt/Stop M
o
n
troller oper
a
e
polymer
m
.
a remote a
n
o
lymer conc
e
C
syste
m
ca
n
u
rposes the s
operating p
a
r
ameters are
r
face Desc
s
ed with Figu
r
q
uences to pr
o
a
nd Syst
e
i
on to the pol
y
T
he sequence
s
sequence ha
s
r
amming inte
6
-7 Polyfeede
r
++ Mode
s
d
e is “Local
O
o
cal” contr
o
t
he mode se
l
o
de
a
tional mode,
m
otely locate
d
s
ed when re
m
o
de with An
a
tional mod
e
m
ixing syste
m
n
alog input s
e
nt
r
ation (p
o
n
be provide
d
yste
m
may
b
a
rameters, s
u
still change
d
ription a
n
r
e 6-7-2, des
c
o
vide functio
21
e
m Oper
y
mer mixing
s
how is whe
n
s
been compl
e
rface can occ
r
Controller
S
s
of Oper
a
O
nly.” All
f
o
l panel inte
r
ector switc
h
remote start
s
d
PLC/SCAD
A
m
otely started.
alo
g
Conce
n
e
is Remote
S
m
is started
a
ignal, the R
e
o
lymer pum
p
d
an analog
f
b
e shut do
w
u
ch as dilut
i
d
locally at
t
n
d System
c
ribes where
a
nality.
ation
system the c
o
n
the system
m
e
ted and elect
r
c
ur.
S
tart Up Scre
e
a
tion
f
unctions re
l
r
face via op
e
h
to PUMP
O
s
top, allows t
h
A
or remote
s
The analog
n
tration C
o
Start Stop
M
a
nd stopped
e
mote Start/
p
pacing).
W
f
eedback pr
o
w
n locally, u
s
i
on water fl
o
t
he cont
r
ol
p
Operatio
n
a
nd how to p
e
o
ntroller LC
D
m
ode selecto
r
t
rical installat
i
en Sequence
l
ated to the
s
e
rator input.
O
FF are the
t
h
e user to sta
r
s
wi
t
ch. In thi
input must
be
o
ntrol
M
ode with A
fro
m
a rem
o
/
Stop mode
c
W
hile in thi
s
o
portional t
o
s
ing the PU
M
o
w rate, bot
h
p
anel interfa
c
n
e
rfor
m
syste
m
D
will report t
h
r
switch is in
t
i
on complete
d
s
yste
m
are c
The Syste
m
t
wo ways to
rt
or stop the
s mode, the c
e
de-activate
d
nalog contr
o
o
te location
u
c
an automat
i
s
mode, the
u
o
polymer fl
o
M
P OFF m
o
h
primary a
n
c
e.
m
operations
a
he basic
t
he local
d
, system
ontrolled
m
start/stop
start/stop
polymer
oncentration
d
to enable
o
l . While i
n
u
sing a dry
i
cally
u
ser’s
o
w rate.
o
de selectio
n
n
d secondar
y
a
nd the
n
n
y