User manual
3-Phase Power Supply Instruction Manual
Bedienungsanleitung für 3-Phasen Stromversorgung
Indicators, LEDs
Overload LED DC-OK LED DC-OK Contact
Normal mode OFF ON Closed
During BonusPower
®
OFF ON Closed
Overload (Vout < 90%) ON OFF Open
Output short circuit ON OFF Open
Temperature Shut-down flashing OFF Open
Active Shut-down input flashing OFF Open
No input power OFF OFF Open
Anzeigelampen
Overload LED DC-OK LED DC-OK Contact
Normalbetrieb AUS EIN geschlossen
Während BonusPower
®
AUS EIN geschlossen
Überlast (Vout < 90%) EIN AUS offen
Ausgangskurzschluss EIN AUS offen
Temperaturabschaltung blinken AUS offen
Aktiver „shut-down“ Eingang blinken AUS offen
Keine Eingangsspannung AUS AUS offen
DC-OK Relay Contact (see Fig. 1)
This feature monitors the output voltage, which is produced by the power supply, and is
independent of a return voltage from a unit which is connected in parallel.
Contact closes when the output voltage is typ. above 90% of the adjusted value.
Contact opens when the output voltage is typ. below 90% of the adjusted value. Short dips will
be extended to a length of 250ms. Dips shorter than 1ms will be ignored.
Contact ratings: max.: 60Vdc 0.3A, 30Vdc 1A, 30Vac 0.5A, resistive load, min. current 1mA
DC-OK Relais Kontakt (siehe Bild 1)
Diese Funktion überwacht die vom Gerät erzeugte Ausgangsspannung und lässt sich von einer
rückwärts eingespeisten Spannung nicht beeinflussen (z.B.: bei Parallelschaltung)
Kontakt schließt wenn die Ausgangsspannung typ. größer als 90% des eingestellten Wertes ist.
Kontakt öffnet wenn die Ausgangsspannung typ. kleiner als 90% des eingestellten Wertes ist.
Kurze Einbrüche werden auf 250ms verlängert. Einbrüche kürzer 1ms werden ignoriert.
Kontakt Belastbarkeit: max.: 60Vdc 0.3A, 30Vdc 1A, 30Vac 0.5A, (R-Last), min. Strom 1mA
Shut-down Input (see Fig. 6)
This feature allows to switch-off the power supply with a signal switch or an external voltage. The
shut-down function has no safety feature included. The shut-down occurs immediately while the
turn-on is delayed by 350ms. In a shut-down condition, the output voltage is <2V and the output
power is <0.5W. The voltage between different –pole output terminals must be below 1V when
units are connected in parallel. In a series operation of multiple power supplies only wiring option
A with individual signal switches is allowed.
„Shut-down“ Eingang (siehe Bild 6)
Abschaltung des Gerätes durch einen Signalschalter oder eine Fremdspannung. Die Abschaltung
beinhaltet keine Sicherheitsfunktionen. Die Abschaltung erfolgt unverzögert, das
Wiedereinschalten mit einer Verzögerung von ca. 350ms. Im abgeschaltetem Zustand ist die
Ausgangsspannung <2V und die Ausgangsleistung <0,5W. Bei parallel geschalteten Geräten
darauf achten, dass der Spannungsunterschied zwischen den Minus Power Klemmen kleiner 1V
ist. Bei Serienschaltung Schaltungsoption A mit getrennten Schaltern verwenden.
Output- and Overload Characteristic
The unit is designed to support loads with a continuous power demand of up to 960W and a short-
term power demand of up to 1440W without damage or shut-down.
Output characteristic (see Fig. 2)
The curve in this figure is a typical curve for 24V unit in “Single Mode”. The other output voltages
have an equivalent and proportional performance.
BonusPower
®
time (see Fig. 3)
The curve in this figure shows the duration until the output voltage starts dipping when more than
960W is drawn (controlled by software).
Ausgangs- und Überlastverhalten
Die Stromversorgung ist zur Versorgung von Lasten mit einem Dauerleistungsbedarf bis zu 960W
und einem kurzzeitigem Leistungsbedarf bis 1440W konstruiert ohne dabei Schaden zu nehmen.
Ausgangskennlinie (siehe Bild 2)
Die Kennlinie in diesem Bild ist die Kennlinie eines typischen 24V Gerätes im “Single Mode”. Die
anderen Ausgangsspannungen zeigen ein proportional vergleichbares Verhalten.
BonusPower
®
Zeit (siehe Bild 3)
Die Kennlinie in diesem Bild gibt die Dauer an bis die Ausgangsspannung sinkt, wenn mehr als
960W entnommen werden (softwaregesteuert).
Parallel-Use to Increase the Output Power
The output voltage shall be adjusted to the same value (±100mV) in “Single mode” at the same
load condition on all units, or shall be left with the factory settings. Afterwards, the jumper on the
front of the unit shall be moved from “single use” to “parallel use”, in order to achieve a load
sharing. The “Parallel Use” mode regulates the output voltage in such a manner that the voltage at
no load is approx. 5% higher than at nominal load. If no jumper is plugged in, the unit is in “Single
Use”. Factory setting is “Single Use”.
Parallelbetrieb zur Leistungserhöhung
Hierzu alle Geräte bei gleicher Belastung im „Single Mode“ auf ±100mV genau einstellen oder die
Ausgangsspannung auf Werkseinstellung belassen. Danach die Steckbrücke an der Front des
Gerätes von „single use“ auf „parallel use“ umstecken, um eine Aufteilung des Laststromes
zwischen den Geräten zu erreichen. In „parallel use“ ist die Ausgangsspannung so geregelt, dass
diese im Leerlauf um etwa 5% höher ist als bei Nennlast. Ein nicht eingesteckter Jumper bedeutet
„single use“. Werkseinstellung ist „single use“.
Dielectric Strength (see Fig. 5)
The output voltage is floating and separated from the input according to SELV (IEC/EN 60950-1)
and PELV (EN 60204-1, EN 50178; IEC 62103, IEC 60364-4-41) requirements. Type and factory
tests are conducted by the manufacturer. Field tests may be conducted in the field using the
appropriate test equipment which applies the voltage with a slow ramp (2s up and 2s down).
Connect all phase-terminals together as well as all output poles before the test is conducted.
A B C D
Type Test (60s) 2500Vac 3000Vac 500Vac 500Vac
Factory Test (5s) 2500Vac 2500Vac 500Vac 500Vac
Field Test (5s) 2000Vac 2000Vac 500Vac 500Vac
Isolationsfestigkeit (siehe Bild 5)
Die Ausgangsspannung hat keinen Bezug zur Erde oder Schutzleiter und ist zum Eingang nach
den SELV (IEC/EN 60950-1) und PELV (EN 60204-1, EN 50178, IEC 62103, IEC 60364-4-41)
Standards getrennt. Typ- und Stückprüfungen werden beim Hersteller durchgeführt.
Wiederholungsprüfungen dürfen mittels geeigneten Prüfgenerators mit langsam (2s)
ansteigenden und abfallenden Spannungsrampen in der Anwendung erfolgen. Vor den Tests sind
alle Phasen wie auch alle Ausgangspole miteinander zu verbinden.
A B C D
Typprüfung (60s) 2500Vac 3000Vac 500Vac 500Vac
Stückprüfung (5s) 2500Vac 2500Vac 500Vac 500Vac
Wiederholungsprüfung (5s) 2000Vac 2000Vac 500Vac 500Vac
Operation on only 2-Phases (see Fig. 4)
No external protection device is required to protect against a phase-loss failure. The power supply
is allowed to run permanently on two phases, when the de-rating requirements are fulfilled. A
long-term exceeding of the de-rating limits will result in a thermal shut-down of the unit. During
power-on, some start-up attempts can occur until a permanent output power is available.
Betrieb an nur 2-Phasen (siehe Bild 4)
Es ist kein externer Schutz gegen Ausfall einer Phase erforderlich. Die Stromversorgung darf
dauerhaft an 2 Phasen betrieben werden, wenn die Ausgangsleistung bei höheren Temperaturen
reduziert wird. Eine dauerhafte Überschreitung dieses Grenzwertes kann zu einer thermischen
Abschaltung des Gerätes führen. Beim Einschalten der Netzspannung kann es zu mehreren
Startversuchen kommen, bevor das Gerät dauerhaft Ausgangsleistung liefert.
Fig. 1 / Bild 1
DC-OK-Signal
Fig. 2 / Bild 2
Output Characteristic /Ausgangskennlinie
Fig. 3 / Bild 3
BonusPower
®
Time / Zeit
Fig. 4 / Bild 4
2-Phase Operation / 2-Phasenbetrieb
Fig. 5 / Bild 5
Insulation / Isolation
250ms
90%
V
ADJ
<
1ms
10%
open
V
OUT
=
V
ADJ
openclosed closed
>
1ms
Output Voltage
0
0 1020 4050
4
8
12
28V
16
20
24
70A30 60
Output Current
s
h
o
r
t
-
t
e
r
m
Adjustment
Range
c
o
n
t
i
n
u
o
u
s
m
a
x
.
Bonus Time
0
110 120 130 140 150
160%
Output Power
1
2
3
4
5s
m
i
n
.
Allowed Output Power
0
-25 0 20
70°C
25%
50%
75%
100%
40 60
A
.
.
.
m
a
x
6
0
s
B
.
.
.
2
x
4
6
0
t
o
5
5
2
V
a
c
C
.
.
.
2
x
3
4
0
t
o
4
6
0
V
a
c
B
A
Ambient Temperature
C
A
D
C
B
B
L1
Input DC-ok
Earth
Output
-
+/-
Shut-down
L3
L2
Fig. 6 / Bild 6
Shut-down Input / Eingang
Fig. 7 / Bild 7
Functional Diagram / Funktionsschaltbild
Fig. 8 / Bild 8
Dimensions / Abmessungen
15
16
OFF: linked /
verbunden
ON : open / offen
Shut-
down
Input
Option A:
15
16
OFF: I > 0.3mA
ON : I < 0.1mA
Shut-
down
Input
Option B:
-
(open collector)
I
15
16
OFF: U < 1V
ON : U = 4 -29V
Shut-
down
Input
Option C:
-
(ext. voltage /
ext. Spannung)
+
U
n.c.
n.c.
+
+
-
-
V
OUT
DC-ok
Contact
Output
Over-
Voltage
Protection
PFC
Converter
Input Fuses
Input Filter
Input Rectifier
Inrush Limiter
Transient Filter
Output
Voltage
Regulator
Power
Converter
Output
Filter
DC ok
Relay
Output
Voltage
Monitor
Output
Power
Manager
Temper-
ature
Shut-
down
Overload
LED
DC-ok
LED
L2
L3
L1
Single /
Parallel
Shut-down
Input
Shut-
down
13
14
15
16
PU-374.010.00-10B