Datasheet

ManualsBrandsPULS ManualsRack & DIN Rail Mount PSUsDIMENSION DIN Rail Power Supply 24Vdc 5A 120W, 2-Phase

CT5.241

C-Series

24V, 5A, TWO-PHASE INPUT

OWER SUPPLY

 AC 380-480V Wide-range Input

 Input Fuses Already Included

 Requires only Two Legs of a 3-Phase System

 Width only 40mm

 Efficiency up to 90.4%

 20% Output Power Reserves

 Input -Transient Blanking Circuit Included

 Minimal Inrush Current Surge

 Full Power Between -25°C and +60°C

 3 Year Warranty

1/21

GENERAL DESCRIPTION

The Dimension C-Series are cost optimized power

supplies without compromising quality, reliability and

performance. The C-Series is part of the DIMENSION

power supply family. The most outstanding features of

CT5.241 are the high efficiency, electronic inrush current

limitation, active input transient filter and wide

operational temperature range, the small size and other

technological design concepts.

The C-Series includes all the essential basic functions.

The devices have a power reserve of 20% included,

which may even be used continuously at temperatures

up to +45°C. The CT5.241 utilizes only 2 legs of a 3-

phase system which saves wiring and installation costs.

Furthermore, this allows a smaller unit without

compromising the size of the terminals. Due to the low

power consumption, an unbalancing of the individual

phases is not expected.

SHORT-FORM DATA

Output voltage DC 24V

Adjustment range 24-28V

Output current 5 – 4.3A ambient <60°C

6 – 5.2A ambient <45°C

Output power 120W ambient <60°C

144W ambient <45°C

Output ripple < 50mVpp 20Hz to 20MHz

Input voltage AC 380-480V -15%/+20%

Mains frequency 50-60Hz ±6%

AC Input current 0.75 / 0.68A at 400 / 480Vac

Power factor 0.45 / 0.43 at 400 / 480Vac

AC Inrush current typ. 4A peak

Efficiency 90.4 / 90.0% at 400 / 480Vac

Losses 12.7 / 13.3W at 400 / 480Vac

Temperature range -25°C to +70°C operational

Derating 3W/°C +60 to +70°C

Hold-up time typ. 27 / 48ms at 400 / 480Vac

Dimensions 40x124x117mm WxHxD

ORDER NUMBERS

Power Supply CT5.241 24-28V Standard unit

Accessory ZM1.WALL Wall mount bracket

ZM12.SIDE Side mount bracket

YRM2.DIODE Decoupling module

UF20.241 Buffer unit

MARKINGS

IND. CONT. EQ.

UL 508

UL 60950-1

Marine,pending

EMC, LVD

Jan. 2010 / Rev. 1.1 DS-CT5.241-EN

All parameters are specified at 24V, 5A, 400Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0 Germany

Summary of content (21 pages)

PAGE 1
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series POWER SUPPLY AC 380-480V Wide-range Input Input Fuses Already Included Requires only Two Legs of a 3-Phase System Width only 40mm Efficiency up to 90.
PAGE 2
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series INDEX Page 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Intended Use .......................................................3 Installation Requirements...................................3 AC-Input...............................................................4 DC-Input...............................................................5 Input Inrush Current ...........................................5 Output ..........................................
PAGE 3
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 1. INTENDED USE This device is designed for installation in an enclosure and is intended for the general use such as in industrial control, office, communication, and instrumentation equipment. Do not use this power supply in aircrafts, trains and nuclear equipment where malfunction may cause severe personal injury or threaten human life. This device is designed for use in non-hazardous, ordinary or unclassified locations. Do not use in hazardous location areas.
PAGE 4
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 3. AC-INPUT AC input nom. AC 380-480V AC input range 323-576Vac Allowed Voltage Phase to Earth Input frequency Turn-on voltage Shut-down voltage Input current Power factor *) Start-up delay Rise time Turn-on overshoot typ. typ. typ. typ. typ. max. AC 400V 0.75A 0.45 75ms 35ms 64ms 200mV AC 480V 0.68A 0.43 75ms 36ms 68ms 200mV at 24V, 5A, see Fig. 3-3 at 24V, 5A, see Fig. 3-1 see Fig. 3-2 0mF, 24V, 5A, see Fig. 3-2 5mF, 24V, 5A, see Fig. 3-2 see Fig.
PAGE 5
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 4. DC-INPUT DC input DC input range Allowed Voltage Line to Earth DC input current Turn-on voltage Shut-down voltage nom. max. typ. typ. typ. DC 600V 450-780Vdc 820Vdc 0.3A / 0.17A 370Vdc 260Vdc Fig. 4-1 Wiring for DC Input Battery + Power Supply AC FUSE FUSE L1 + L2 Load - PE - DC continuous operation IEC 62103 450Vdc / 780Vdc, 24V, 5A steady state value steady state value Instructions for DC use: a) Use a battery or similar DC source.
PAGE 6
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 6. OUTPUT Output voltage Adjustment range nom. min. max. Factory setting Line regulation Load regulation Ripple and noise voltage Output capacitance Output current 24V 24-28V 30V 24.1V 10mV 100mV 50mVpp 3 800μF 6A 5A 5.2A 4.3A 144W 120W 10A 13A max. max. max. typ. nom. nom. nom. nom. nom. nom. min. max. Output power Short-circuit current guaranteed at clockwise end position of potentiometer ±0.
PAGE 7
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 7. HOLD-UP TIME Hold-up Time typ. typ. Fig. 7-1 Hold-up time vs. input voltage AC 400V 27ms 51ms AC 480V 48ms 91ms at 24V, 5A, see Fig. 7-1 at 24V, 2.5A, see Fig. 7-1 Fig. 7-2 Shut-down behavior, definitions Hold-up Time at 24Vdc 80ms p ty A, 5 . 2 60 . Zero Transition . in ,m A 2 .5 , 5A 40 . typ . min 5A, 20 Input Voltage Hold-up Time Input Voltage 0 320 360 400 - 5% Output Voltage 440 480Vac Jan. 2010 / Rev. 1.1 DS-CT5.
PAGE 8
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 8. EFFICIENCY AND POWER LOSSES Efficiency Average efficiency *) typ. typ. AC 400V 90.4% 88.8% AC 480V 90.0% 87.9% Power losses typ. typ. typ. 1.5W 12.7W 15.3W 1.6W 13.3W 15.8W *) at 24V, 5A 25% at 1.25A, 25% at 2.5A, 25% at 3.75A.
PAGE 9
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 9. FUNCTIONAL DIAGRAM Fig. 9-1 Functional diagram L1 L2 Input Fuses PFC Inductor Input Filter Inrush Limiter Input Rectifier Temperature Shutdown Power Converter Output Filter Transient Filter Output Power Manager Output OverVoltage Protection Output Voltage Regulator + + VOUT DC-ok LED 10. FRONT SIDE AND USER ELEMENTS Fig.
PAGE 10
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 11. TERMINALS AND WIRING Type Solid wire Stranded wire American Wire Gauge Wire stripping length Screwdriver Recommended tightening torque Input screw terminals 0.5-6mm2 0.5-4mm2 20-10 AWG 7mm / 0.275inch 3.5mm slotted or Pozidrive No 2 0.8Nm, 7lb.in Output screw terminals 0.5-6mm2 0.5-4mm2 20-10 AWG 7mm / 0.275inch 3.5mm slotted or Pozidrive No 2 0.8Nm, 7lb.
PAGE 11
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 13. EMC The power supply is suitable for applications in industrial environment as well as in residential, commercial and light industry environment without any restrictions. The CE mark indicates conformance with EMC guideline 89/336/EC, 93/68/EC and 2004/108/EC and the low-voltage directive (LVD) 73/23/EC and 2006/95/EC. A detailed EMC report is available on request.
PAGE 12
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 14. ENVIRONMENT Operational temperature *) Storage temperature Output de-rating Humidity **) Vibration sinusoidal Shock Altitude Altitude de-rating Over-voltage category -25°C to +70°C (-13°F to 158°F) -40 to +85°C (-40°F to 185°F) 1.6W/°C 3W/°C 5 to 95% r.H. 2-17.8Hz: ±1.6mm; 17.8-500Hz: 2g 2 hours / axis 30g 6ms, 20g 11ms 3 bumps / direction, 18 bumps in total 0 to 6000m (0 to 20 000ft) reduce output power according Fig.
PAGE 13
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 15. PROTECTION FEATURES Output protection Output over-voltage protection Electronically protected against overload, no-load and short-circuits *) typ. 30.5Vdc In case of an internal power supply defect, a redundant max. 32Vdc circuit limits the maximum output voltage. The output shuts down and automatically attempts to restart. IP 20 EN/IEC 60529 > 3.5mm e.g.
PAGE 14
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 18. APPROVALS IEC 60950-1 CB Scheme, Information Technology Equipment UL 508 Listed for use as Industrial Control Equipment; U.S.A. (UL 508) and Canada (C22.2 No. 107-1-01); E-File: E198865 Mains supply circuit: 3-wire + PE, star Recognized for use as Information Technology Equipment; U.S.A. (UL 60950-1) and Canada (C22.2 No.
PAGE 15
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 21. PHYSICAL DIMENSIONS AND WEIGHT Weight DIN-Rail Installation Clearances 500g / 1.1lb Use 35mm DIN-rails according to EN 60715 or EN 50022 with a height of 7.5 or 15mm. The DIN-rail height must be added to the unit depth (117mm) to calculate the total required installation depth. See chapter 2 Fig. 21-1 Front view Fig. 21-2 Side view Jan. 2010 / Rev. 1.1 DS-CT5.
PAGE 16
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 22. ACCESSORIES ZM1.WALL Wall mounting bracket This bracket is used to mount specific Dimension units onto a flat surface without utilizing a DIN-Rail. The two aluminum brackets and the black plastic slider of the unit have to be removed, so that the two steel brackets can be mounted. Fig. 22-1 ZM1.WALL Wall mounting bracket *) Fig. 22-2 Assembled wall mounting bracket *) Picture of the power supply is for representation only ZM12.
PAGE 17
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 23. APPLICATION NOTES 23.1. PEAK CURRENT CAPABILITY Solenoids, contactors and pneumatic modules often have a steady state coil and a pick-up coil. The inrush current demand of the pick-up coil is several times higher than the steady-state current and usually exceeds the nominal output current (including the PowerBoost) The same situation applies, when starting a capacitive load. Branch circuits are often protected with circuit breakers or fuses.
PAGE 18
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 23.3. CHARGING OF BATTERIES The power supply can be used to charge lead-acid or maintenance free batteries. (Two 12V batteries in series) Instructions for charging batteries: a) Ensure that the ambient temperature of the power supply is below 45°C b) Set output voltage (measured at no load and at the battery end of the cable) very precisely to the end-of-charge voltage. End-of-charge voltage 27.8V 27.5V 27.15V 26.
PAGE 19
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 23.6. EXTERNAL INPUT PROTECTION The unit is tested and approved for branch circuits up to 30A (U.S.A.) and 32A (IEC). An external protection is only required, if the supplying branch has an ampacity greater than this. Check also local codes and local requirements. In some countries local regulations might apply. If an external fuse is necessary or utilized, minimum requirements need to be considered to avoid nuisance tripping of the circuit breaker.
PAGE 20
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 23.9. DAISY CHAINING OF OUTPUTS Daisy chaining (jumping from one power supply output to the next) is allowed as long as the average output current through one terminal pin does not exceed 25A. If the current is higher, use a separate distribution terminal block. Fig. 23-4 Daisy chaining of outputs Fig.
PAGE 21
CT5.241 24V, 5A, TWO-PHASE INPUT C-Series 23.12. MOUNTING ORIENTATIONS Mounting orientations other than input terminals on the bottom and output on the top require a reduction in continuous output power or a limitation in the max. allowed ambient temperature. The amount of reduction influences the lifetime expectancy of the power supply. Therefore, two different derating curves for continuous operation can be found below: Curve A1 Curve A2 Recommended output current.