User Manual SC51T PTN Compact Scaler Switcher All Rights Reserved Version: SC51T (with PoC) 2013V1.0 www.PTN-electronics.
Compact Scaler Switcher (with PoC) NOTICE: 1. Please read this user manual carefully before using this product. 2. The item PoC is short for Power over Cable. 3. The receiver works with SC51T can only be TPHD402PR. 4. The item “far-end” means the device (e.g. display device, 3rd party RS232 device etc) connected with TPHD402PR. 5. Take notice to 4.6 Instructions of VGA Converting Cable when using. This manual is for operation instruction only, not for any maintenance usage.
Compact Scaler Switcher (with PoC) Table of Contents 1. Introduction .................................................................................................................1 1.1 Introduction to SC51T ........................................................................................ 1 1.2 Features ............................................................................................................ 1 1.3 Package Contents .................................................................
Compact Scaler Switcher (with PoC) 4.4 Operations of RS232 Control........................................................................... 14 4.4.1 Installation/uninstallation of RS232 Control Software ............................ 14 4.4.2 Basic Settings ........................................................................................ 14 4.4.3 RS232 Communication Commands ...................................................... 15 4.4.4 Control SC51T or 3rd Party Device from Local...................
Compact Scaler Switcher (with PoC) 1. Introduction 1.1 Introduction to SC51T SC51T is a compact mini scaler switcher with 5 video inputs (3 HDMI, 2 VGA) and 6 audio inputs (3 HDMI audio & 2 VGA audio: switched following the video; 1 MIC audio input). As the VGA input supports VGA, YPbPr and C-video, so the scaler switcher is compliant with multiple video signals.
Compact Scaler Switcher (with PoC) 1 x RS232 cable 2 x VGA converting cables (male VGA to female YPbPr, length: 400 mm) 7 x Captive screw connectors 4 x Screws (black color) 6 x Plastic cushions 1 x User Manual Notes：Please confirm if the product and the accessories are all included, if not, please contact with the dealers. 2. Product Appearance 2.1 SC51T Front Panel ① Power indicator. Turns red when power on, turns green when in standby mode.
Compact Scaler Switcher (with PoC) ⑤ RESO/AUTO Used as output resolution manual switching button, select between 1360x768, 1280x800, 1280x720, 1024x768, 1920x1200, 1920x1080 and 1600x1200. Used as output resolution switching mode selection button, press and hold on 3 seconds or more to enter in Auto-switching mode, press and hold on 3 seconds or more again to enter in Manual-switching mode. ⑥ MENU/FWUPDATE Used as menu button, press it to enter in OSD menu.
Compact Scaler Switcher (with PoC) ① AUDIO INPUT 3 HDMI audio & 2 VGA audio inputs. User can choose any one audio (embedded HDMI audio or external input audio) for HDMI audio input by using RS232 commands. ② AUDIO OUTPUT Audio output port, the audio comes from the input audio corresponding to the selected video source and mixed with MIC audio. ③ IR OUT 5 ports in total. Connects with IR emitter, used to control local source device or SC51T from remote, switches following the corresponding video source.
Compact Scaler Switcher (with PoC) 3. System Connection 3.1 Usage Precautions 1) System should be installed in a clean environment and has a prop temperature and humidity. 2) All of the power switches, plugs, sockets and power cords should be insulated and safety. 3) All devices should be connected before power on. 3.2 System Diagram 3.3 Connection Procedure Step1. Connect HDMI source devices (e.g. Blue-ray DVD) to HDMI input ports of SC51T with HDMI cable. Connect VGA source device (e.g.
Compact Scaler Switcher (with PoC) IR signal receiver, the IR signal must be sent out by the other model. For example: When “IR IN” of SC51T connects with an IR receiver, the IR transmitter must connect to IR OUT of TPHD402PR. The IR signal can be transmitted bi-directionally between SC51T and TPHD402PR. Step8. Select MIC level and connect right microphone to MIC input port. MIC audio will be transmitted to AUDIO OUTPUT port and mixed with source audio. Step9.
Compact Scaler Switcher (with PoC) 2) Balanced connection: “+” connects to positive, “-” connects to negative and “ connects to ground. ” LINE input When switch to “LINE” (It has a low frequency characteristics, and wide frequency response in this mode), the microphone input is used for connecting with line audio or wireless microphone output. There are two different connections: Unbalanced connection: “+” and “ ” connect to ground, and “-” connects to signal.
Compact Scaler Switcher (with PoC) 3.5 Application SC51T has a good application in various occasions, such as computer realm, monitoring, conference room, big screen displaying, television education, command & control center and smart home etc. 4. System Operations 4.1 Operations of Buttons The buttons can be used for output resolution adjusting, switching operations, software updating, volume adjusting and operations in menus. 4.1.1 Resolution Adjusting Supports auto-adjusting and manual-adjusting.
Compact Scaler Switcher (with PoC) Auto-switching function The auto-switching mode follows the listed principles: New input principle Once detecting a new input signal, SC51T would switch to this new signal automatically. Power rebooting principle SC51T offers the function to remember the signal last displayed when rebooting. Once rebooting, SC51T will automatically enter in auto-switching mode, and then detect all inputs and memorize their connection status for future rebooting using.
Compact Scaler Switcher (with PoC) 4.1.3 Software Updating Software updating means to update the inside program of this scaler switcher. SC51T supports software updating via USB flash disk. The Operation is: 1) Copy the file “MERGE.bin” to a USB flash disk. (The “MERGE.bin” file is provided/authorized by PTN engineering department or from our website: http://www.PTN-electronics.com) 2) Plug the USB flash disk to the SC51T USB port on its front panel.
Compact Scaler Switcher (with PoC) 4.2 Operations of IR 4.2.1 IR Remote As IR signal can be transmitted bi-directionally between SC51T and TPHD402PR, it is able to use the IR remote at the far-end to control SC51T or HDMI source devices (via CEC function buttons). ① Standby button To enter in/exit standby mode. ② Input channel selection buttons INPUT 1 is for HDMI1, INPUT 2 for HDMI2…INPUT 5 for VGA2. AUTO button: Enable/disable auto-switching mode.
Compact Scaler Switcher (with PoC) 4.2.2 IR Operations The 5 IR OUT ports are corresponding to the 5 video inputs one to one, and switch following the corresponding video source. 1) Control far-end device from local To control SC51T or far-end display device from local by using corresponding remote controller. 2) Control local device from remote To control SC51T or local source device from remote by using corresponding remote controller. PTN Electronics Limited 12 www.PTN-electronics.
Compact Scaler Switcher (with PoC) 4.3 Operations of CEC Function Supports CEC and CEC standby functions, and can be enabled/disabled through RS232 commands or OSD menu. If the HDMI source device supports CEC, and when SC51T enter in standby/startup mode, then the source device will automatically enter in standby/startup mode. And due to CEC function, user can control HDMI source device with basic operations (play, pause, fast forward, fast reverse, menu etc).
Compact Scaler Switcher (with PoC) CEC: Control HDMI source devices by IR remote of SC51T 4.4 Operations of RS232 Control As RS232 can be transmitted bi-directionally between SC51T and TPHD402PR, so it is able to control a third party RS232 device from local or control SC51T from remote. When to control a third party RS232 device, the baud rate of this device should be 2400, 4800, 9600, 19200, 38400, 57600 or 115200. 4.4.
Compact Scaler Switcher (with PoC) Parameter Configuration area Monitoring area, indicates if the command sent works. Command Sending area Please set the parameters of COM number, bound rate, data bit, stop bit and the parity bit correctly, and then you are able to send command in Command Sending Area. 4.4.
Compact Scaler Switcher (with PoC) 50621% 50626% 50627% 50628% 50629% Preset the contrast. The XX is ranging from 00 to 99 Preset the saturation. The XX is ranging from 00 to 99 Preset the sharpness.
Compact Scaler Switcher (with PoC) 50647% Disable MIC Volume Bar display 50648% Enable HDMI embedded audio output 50649% Disable HDMI embedded audio output 50651% Check Volume Bar display status 50652% Check Digital audio output status 50655% 50656% 50698% 50701% 50702% 50703% 50704% 50705% Freeze output image Cancel the freezing of output image Software (inside program) update Switch to HDMI 1 input (INPUT 1) Switch to HDMI 2 input (INPUT 2) Switch to HDMI 3 input (INPUT 3) Switch to VGA 1 input
Compact Scaler Switcher (with PoC) 50754% 50787% 50788% Check the panel locked status Enable serial control mode 1 (control SC51T & far-end from local) Enable serial control mode 2 (control SC51T from local or far-end) Panel Locked/Unlocked Pc control far end Far end control 51T 50761% Not display mute icon of LINE audio in OSD 50762% Display mute icon of LINE audio in OSD 50763% Not display mute icon of MIC audio in OSD 50764% Display mute icon of MIC audio in OSD 50765% 50766% 50780% 50781% 50
Compact Scaler Switcher (with PoC) 50676% 50677% 50678% Stretch upwards from top side (increase image height) Stretch upwards from down side (decrease image height) Enable screen output adjusting (then able to adjust screen output through OSD menu) 50679% Disable screen output adjusting 50680% Select VGA source for INPUT 4 (VGA 1) 50681% Select YPbPr source for INPUT 4 (VGA 1) 50682% Select C-video source for INPUT 4 (VGA 1) 50683% Select VGA source for INPUT 5 (VGA 2) 50684% Select YPbPr sourc
Compact Scaler Switcher (with PoC) 4.4.4 Control SC51T or 3rd Party Device from Local Firstly, connect the RS232 port of SC51T to RS232 port of PC. Secondly, send command 50787% (serial control mode 1, factory default) via RS232 communication software. Lastly, send the right command of SC51T or other remote RS232 device connected in present system. Connect as below: Control SC51T or 3rd party device from local 4.4.
Compact Scaler Switcher (with PoC) Control SC51T from local Control SC51T from remote Firstly, connect the RS232 port of far-end RS232 device to RS232 port of PC. Secondly, send command 50788% via RS232 communication software. Lastly, send the right command to control SC51T. Connect as below: Control SC51T from remote 4.5 Operations in OSD Menu SC51T provides a powerful OSD operation menu, contains 4 parts: optional settings, image settings, audio settings and system setting etc.
Compact Scaler Switcher (with PoC) 4.5.1 Option Includes Software Update (USB), Output Adjust, Input4 Select and Input5 Select. Software Update (USB): Insert the USB flash disk with updating file to USB port of SC51T, to update the software through this menu. Output Adjust: Adjust output image position (X: horizontal direction and Y: vertical direction) and ratio aspect (width and height).
Compact Scaler Switcher (with PoC) 4.5.2 Picture Including Picture Mode, Color Temperature, Aspect Ratio, Noise Reduction, Screen and Color Range. Please check the picture below: Picture mode: Includes Dynamic, Standard, Mild, and User. And only in User mode, it is able to set the image contrast and brightness. Color Temperature: Includes Cool, Medium, Warm and User. And only in User mode, it is able to set values for Red, Green and Blue (RGB).
Compact Scaler Switcher (with PoC) 4.5.3 Sound Including Sound Mode, Surround Sound and EQ. Please check the picture below: Sound mode: Includes Standard, Music, Movie, Sports and User. Only User mode supports to set treble and bass. Surround Sound: Includes Off, Surround and SRS Trusurround XT. EQ: To adjust the sound balance. PTN Electronics Limited 24 www.PTN-electronics.
Compact Scaler Switcher (with PoC) 4.5.4 Setup Including OSD Language, Blending, HDMI CEC and OSD Duration. OSD Language: Supports 14 languages, including English (default), Chinese etc. Blending: Includes Low, Middle, High and Off. Use ENTER button to select. HDMI CEC: Enable/disable CEC and auto-standby function. Default: CEC on, STANDBY on. OSD Duration: Includes 5 s, 10 s, 15 s and Off. “s” is for Second. 4.
Compact Scaler Switcher (with PoC) YPbPr2 source. 2. Via RS232 commands Send command 50681% (or 50684%) to switch to YPbPr1 (or YPbPr2) source. 3. Via IR remote & OSD Press MENU button on IR remote to enter in OSD, and then enter in OPTION setting menu: set “INPUT 4 Select” to YPbPr1, and “INPUT 5 Select” to YPbPr2. After setting, press INPUT 4 (or INPUT 5) button to switch to YPbPr1 (or YPbPr2) source. B. Connecting the VGA converting cable like this: Connect with Composite Video (C-VIDEO) Source A.
Compact Scaler Switcher (with PoC) 5. Specification Video Input Input Input Connector Video Signal Video Output 3 HDMI 2 VGA 3 female HDMI 2 female VGA (15 pin) HDMI, YPbPr, C-video, VGA Output Output Connector Video Signal IR Input Input 1 IR IN Input 3.
Compact Scaler Switcher (with PoC) Control/ Remote General Temperature IR remote, Buttons & RS232 Pin Configuration 2 = TX, 3 = RX, 5 = GND -20 ~ +70℃ Humidity Power Supply DC12V ± 0.5V Power Consumption 10% ~ 90% 8W, supply power to SC51T and TPHD402PR separately Case Dimension W220x H44x D148mm Product Weight 16W, SC51T supplies power to TPHD402PR 0.67Kg 6. Panel Drawing PTN Electronics Limited 28 www.PTN-electronics.
Compact Scaler Switcher (with PoC) 7. Troubleshooting & Maintenance 1) When output image is with snowflake, such as the projector output with snowflake. Generally this is not a unit faulty, Caused by a bad quality of cable. Please try another high quality cable. The video cables are loose, please connect again. 2) When it is not able to manage EDID, maybe the HDMI cable is broken or loose.
Compact Scaler Switcher (with PoC) 8. Safety Operation Guide In order to guarantee the reliable operation of the equipments and safety of the staff, please abide by the following proceeding in installation, using and maintenance: 1) The system must be earthed properly. Please do not use two blades plugs and ensure the alternating power supply ranged from 100v to 240v and from 50Hz to 60Hz. 2) Do not put the device in a place of too hot or too cold.
Compact Scaler Switcher (with PoC) 9. After-sales Service 1) If there appear some problems when running SC51T, please check and deal with the problems reference to this user manual. Any transport costs are borne by the users during the warranty. 2) You can email to our after-sales department or make a call, please tell us the following information about your cases. Product version and name. Detailed failure situations. The formation of the cases.
www.PTN-electronics.com PTN Electronics Limited Tel: +86-755-2846 1819 Fax: +86-755-8471 7796 Email: info@PTN-electronics.com Website: www.PTN-electronics.
