Installation and Operation Manual for Intelligence Dome Camera V1.
SAFETY PRECAUTIONS
INDEX 1.Important Safeguards------------------------------------------------------------1 2.Description of Functions -------------------------------------------------------3 2.1 Integrated Multi-Protocol Decoder-------------------------------------3 2.2 Integrated Speed-Variable PAN/TILT----------------------------------3 2.3 High Intelligent Degree----------------------------------------------------4 2.4 Functions of the Camera--------------------------------------------------5 3.
1. Points for Attention 1. All the safety and operating instructions should be read before the units is operated. 2. This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply you plan to use, consult your appliance dealer or local power company. For units intended to operate from battery power or other sources, refer to operating instructions. 3.
. The product should be indoor installed and operated to avoid rain and moisture. Do not use it in wet places. If outdoor installation is needed, the closed protect cover should be used and it is absolutely prohibited to use it in open air independently. 7. Do not operate it in case temperature, humidity and power supply are beyond the limited stipulations. 8. Do not let the camera aim at the sun or the object with extreme light whatsoever it is switched on or not.
2. Description of Functions The intelligent dome camera is a hi-tech CCTV product which incorporates high-clarity color camera, panoramic speed-variable PAN/TILT, multifunctional decoder, universal character generator, CPU processor, memory chip into a whole. It can largely reduce connection and installation processes of components in the system, rise up reliability of the system and facilitate installation and maintenance.
3. High Intelligent Degree a. Dome general functions a. As much as 128 preset positions can be preset with powerless memory b. The camera can scan horizontally between two points and scan speed can be modified. The positions of linear scan are optional and the dome camera can scan the range larger or smaller than 180° between any two points with adjustable speed. c. Six sets of programmable tour locus with 16 position each set. The running speed and the detention time are adjustable respectively; d.
4. Functions of the Camera (icons can be displayed on the screen when the option DISPLAY of the camera is ON，Only for 18× Camera) a. Description of the Focus Control Mode: the user can adjust the focus of the camera manually. When the camera is on near focus, the icon appears on the screen; when on the nearest state, the icon appears while on the far focus, the icon appears. b.
3. Setup of the Menu of the Dome Camera 1. Basic Operation of the Menu 1.1 Call preset 64 or call preset 1 twice within 4 seconds to enter the main menu by the control keyboard or by the matrix. 1.2 When the menu is displayed on the screen, operate “TILT UP”, “TILT DOWN”to move the cursor to the option to be set, operate “PAN LEFT”, “PAN RIGHT”to modify the content or the order to enter this option. 1.3 Keep the joystick in one direction for over 1 second to speed up operation. 1.
2.1.7 2.1.8 2.1.9 CAM DEFAULT SET: to reset default setup of camera. DOME RESET: to reset the dome camera. EXIT: to quit the main menu. 2.2 DISPLAY SETUP 2.2.1 ID DISPLAY: when it is set at ON, address of dome camera appears on the screen such as “CAM 001”. The default setting is ON. 2.2.2 ID POS: to set the display position of address on one of following corners: TOP-L, TOP-R, BOTT-R and BOTT-L. 2.2.3 TITLE DIS: when it is set at ON, the title of preset point appears on the left of screen such as "NO.
2.3.7 WB SET: setup of white balance. ATW / INDOOR / OUTDOOR / ONEPUSH / AUTO / MANU 2.3.8 MENU OF CAM: blank 2.3.9 RETURN: return to MAIN MENU 2.4 CONTROL SETUP 2.4.1 AUTO FLIP: 180°automatic flip of dome camera ON/OFF. 2.4.2 ALARM: ALARM ON/OFF switch 2.4.3 PRESET PIC: NOP 2.4.4 HOME OPTION: enter the submenu of automatic home function. 2.4.4.1 AUTO HOME: when it is set at ON, home function is available, namely, the dome camera will return HOME if user has no action in a period of time.
2.5 CAMERA MASK SET 2.5.1 MASK PRIVACY: ON/OFF 2.5.2 MASK SHADE: BLACK/GRAY/WHITE 2.5.3 MASK REGION: 6 or 2 privacy zone masking.(only for part of camera) 2.5.4 RETURN: return to Main Menu 2.6 PROGRAM Options 2.6.1 AUTO PAN START POS: To set start position of auto scan between two points. To move the dome camera by joystick after entering and to return by CLOSE button. 2.6.2 AUTO PAN END POS: To set end position of auto scan between two points.
edit by CLOSE button. Operations under edit state can be seen later. 2.6.5 SET PATROL: to edit data for multi-points patrol. Select no. of patrol by PAN LEFT/PAN RIGHT, enter into edit by OPEN button and exit edit by CLOSE button. Operations under edit state can be seen later. 2.6.6 RUN PATROL: to run multi-points patrol function. Select no. of patrol by PAN LEFT/PAN RIGHT, run and exit by OPEN button. 2.6.7 RECORD PATTERN: This pattern can consist of any standard pan and tilt or lens command.
Both top and bottom lines display prompt and information of each patrol is displayed on the middle of the screen. Data of 2 Patrol points appears on one line. Move cursor by PAN LEFT/RIGHT and modify data by TILT UP/DOWN. Press buttons for one second to speed up operation. Press CLOSE button to exit edit state and store modifications. The program will search the position of the first “---”of POS, store dada before it and regard data after it as invalid.
4. Setup of the Dome Camera 1.
b. Figure 2 Middle speed and low speed dome Figure 3 As shown in Figure 2,3, SW1 is used to set address of the dome camera from 1 – 1023. The coding switches from DIP-10 to DIP-1 are equivalent to a 10-bit binary digital. DIP-10 is MSB while DIP-1 is LSB. The state “ON”of each bit means 1 while “OFF”means 0. Following table shows states of coding switches of some addresses.
5 ON OFF ON OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF 9 ON OFF OFF ON OFF 10 OFF ON OFF ON 11 ON ON OFF 12 OFF OFF 13 ON 14 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF OFF 15 O
Protocols DIP status Normal Baud Rate DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 SAMSUNG ON OFF OFF OFF OFF ON B01 ON OFF OFF OFF OFF ON NEON ON OFF OFF OFF OFF ON Santachi OFF ON OFF OFF OFF ON PELCO-D ON ON OFF OFF OFF OFF OFF OFF ON OFF ON OFF OFF ON PANASONIC ON OFF ON OFF OFF ON Longcomity OFF ON ON OFF OFF ON HUNDA600 ON ON ON OFF OFF ON LILIN OFF OFF OFF ON OFF ON VICON ON OFF OFF ON ON OFF MOLYNX OFF ON OFF ON OFF
3. Setup of the Baud Rate of Communication. As shown in Figure 2,3 SW2 is used to set the protocol of communication and the baud rate used by the dome camera. DIP-6 and DIP-5 of SW2 are used to select the baud rate of communication and 4 different baud rates can be selected in maximum. If the controller adopts non-standard baud rate, you can adjust it to be identical with that of the main machine as per the following table.
5. The Installation of the System 1. Dimension of the Product Figure 4 2.
c) Product disposition overall size Indoor wall Installation outdoor wall installation indoor/outdoor In-Ceiling installation Figure 7 3. The step of high speed dome installs (taking wall-installing style as example) 1) Unpacking the carton and carefully take out the dome camera and its attachments. 2) Take out system control wires from the bracket (see Figure 8). 3) Fix the bracket on the wall with the M6 (see Figure 9).
Figure 10 Figure 11 Figure 12 5) Fix the pedestal in the aluminum alloy ball (Figure 11). Install the ball on the bracket (Figure 12).
7) Insert attachment plug in aluminum alloy into socket D2 (Figure 15) . According the fig of D3 to connection. As show of fig47 when dome identify the alarm signal, that will set according the program immediately, then startup camera, switching the image of alarm field to main monitor. Surveillance the alarm preset, then record it in time. Fig16 is connection of alarm control 8) Input of alarm: Input signal of switch type, any other input signal will damage dome.
9) Based on the coding switches shown as Figure 2, set up the protocol used by the camera and the baud rate as per the state according to Table 2. Check the address of the camera to see if it is matched with that you need. If not, set the address of the dome camera at corresponding position as per Table 1. 10) Rotate the vitreous cover on dome counterclockwise and take it out. Note: if Fixed the Speed Dome Camera in the aluminum alloy ball, you must take out the vitreous cover on dome.
7) a step of operation. 3) 4 bolts black coats which the inside lining squeeze out, take down the inside lining black cover(Figure 21) 4) Based on the coding switches shown as Figure 2, set up the protocol used by the camera and the baud rate as per the state according to Table 2. Check the address of the camera to see if it is matched with that you need.
Figure 24 9) Fixes the support on the wall (Figure 26) 10) Fixes the dome to the support above Figure 25 Figure 26 11) System pilot wire after (Figure 27 ) marking meets, after the electricity then controlled the ball machine for the system on. RED LINE(AC24V IN) BLACK LINE(AC24V IN) ORANGE LINE(RS485+) YELLOW LINE(RS485-) RED CONNECTOR (POWER IN) BLACK CONNECTOR (RS485 CONTROL IN) VIDEO OUT Figure 27 5.
(Figure 28) 3) Take out system control wires from the bracket(Figure 29) 4) Fixes the ball cover to the support above(Figure 30) 5) System pilot wire after (Figure 15) marking meets, after the electricity then controlled the ball machine for the system on. Figure 28 6. Figure 29 Figure 30 To Ensure a Smooth and Successful Installation, You Should: 1) Have electrical work to comply with latest national electrical code, national fire code, and all applicable local codes and ordinances.
6. Technical data table 1.
Synchronization Internal Preset position 64 Cruising track 6 Pan scanning 360°programably Pan speed Maximum 80°/s Pan range 360°continuously Tilt range 0-- 90° Tilt speed Maximum 12°/s Communication RS485 Baud rate 2400/4800/9600/19200 bps Relative humidity 10-75%（without agglomeration） Work temperature Indoor：0℃ — +40℃ Outdoor：–35℃ -- +55℃ Table 5 3.
Iris Auto/ Manual Focus Auto/ Manual Zoom Rate 16× optical 18× optical 22× optical 23× optical 27× optical f=3.9 to 63 mm f=4.1 to 73.8 mm f=4 to 88 mm f=3.6 to 82.8 mm f=3.6 to 98 mm Wide: 47° Wide: 48° Wide: 47° Wide: 54° Angel of view TELE: 3° TELE:2.7°TELE:2.2°TELE:2.5° B.L compensation Auto/ Manual White balance Auto/ Manual Gain Control Auto/ Manual S/N ≥50dB >46dB Video output 1.0±0.2Vp-p Table 6 4. Middle/low speed dome Special function control.
58 59 60 61 62 63 64 have it’ s own menu, to open/close the menu by the command “turn on the OSD”, and use the command “turn off the OSD”to open/close the OSD) Digital Zoom FOCUS IRIS On Auto Auto Auto White Balance Mode Indoor ATW Frame pile function switch able Table 7 Off Manual Manual Manual Outdoor One Push WB 7.
Vague image Dome camera out of control Protocol setup is wrong Reset and Switch ON again Bad connection of the video Press to connect well Power supply not enough Replace Self check error Switch ON again Bad connection of control Press to connect well Bad control of matrix Switch ON again Table 8 Appendix Ⅰ: Lightning Proof and Surge Signal Proof The product adopts TVS lightning proof technology to prevent from damage by lightning strike below 1500 W and impulse signals such
electricity net. When the system is grounded separately, the resistance of down conductor should be ≤ 4Ω and the sectional area of down conductor should be ≤25 mm2 (refer to Picture 59) Figure 31 Appendix Ⅱ: The Cleaning of Clear Down Cover To obtain constant clear videos, user should clean the down cover periodically. Be cautious when cleaning. Hold the down cover ring only to avoid direct touch to the acrylic down cover.
Appendix Ⅲ: RS485 Bus Basic Knowledge 1. Characteristics of RS485 Bus As specified by RS485 standards, RS485 Bus is of half-duplexed data transmission cables with characteristic impedance as 120Ω. The maximum load capacity is 32 unit loads (including main controller and controlled equipment). 2. Transmission distances of RS485 Bus When user selects the 0.
A+ . . . . . BD A+ B. . . . . 120Ω Main controller 1# 2# 3# 120Ω 31# Figure 33 The connection of 120Ω termination resistor: The termination resistor is ready on the Protocol PCB. There are two kinds of connection. Refer to the Protocol PCB jumper setting form (refer to Picture 2,3). 1) In the Picture it is the factory default connection. The jumper is seated on Pin2&Pin3 and the termination resistor is not connected.
Figure 34 In such circumstances the factory recommends the usage of DR-HB16 RS485 distributor. The distributor can change the star configuration connection to the mode of connection stipulated in the RS485 standards. The new connection achieves reliable data transmission (refer to Picture 35).
Appendix Ⅳ: Wire Diameter and Transmission Distance Comparison Chart Wire diameter (mm) Transmission Distance 0.8000 1.000 1.250 2.
Appendix Ⅴ : Wire Gauge Conversion Chart Bare wire diameter metric size （mm） AWG (Approximate) SWG (Approximate) Bare wire cross sectional area （mm2） 0.050 43 47 0.00196 0.060 42 46 0.00283 0.070 41 45 0.00385 0.080 40 44 0.00503 0.090 39 43 0.00636 0.100 38 42 0.00785 0.110 37 41 0.00950 0.130 36 39 0.01327 0.140 35 0.160 34 0.180 33 0.200 32 0.230 31 0.250 30 33 0.04909 0.290 29 31 0.06605 0.330 28 30 0.08553 0.350 27 29 0.09621 0.
0.900 19 20 0.6362 1.000 18 19 0.7854 1.250 16 18 1.2266 1.500 15 2.000 12 1.7665 14 3.1420 2.500 4.9080 3.000 7.
CCTV SYSTEM
