User's Manual

ManualsBrandsPsion ManualsElectronicsRFID MODULE UHF-CA3-AC5-GPRS

WORKABOUT PRO G2 RFID MODULE UHF-CA3-AC5-GPRS

EXPANSION MODULE INSTRUCTIONS

Important:

All Approval and safety information is outlined in the ‘Workabout pro G2 Handheld-computer

User Manual’ – part number 8100140A. This manual is available on our website www.psionteklogix.com

through the Psion Teklogix community website.

Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to

meet your specific mobile computing requirements. This chapter outlines how to install the RFID Module

UHF-CA3-AC5-GPRS.

Before installing a module in the WORKABOUT PRO G2, all power sources must be turned off.

• Remove the batteries. If your unit is using AC power, disconnect it.

WAP C G2 WAP S G2

• Slide the switch to position OFF to shut off internal battery power.

With the power shut down, you can install the RFID Module UHF-CA3-AC5-GPRS.

• Installing the GPRS Radio Module

The GSM/GPRS (model RA3030-G2) radio module includes a radio and an antenna, and includes a SIM

card holder. The SIM card, required to use the radio, is sold separately.

This radio module requires an end-cap with a protrusion to accommodate the antenna.

The GSM/GPRS expansion module aligns with mating connectors in the WORKABOUT PRO:

April 07, 2010

DPD A00515 A00 Sheet 1 of 12

Summary of content (11 pages)

PAGE 1
WORKABOUT PRO G2 RFID MODULE UHF-CA3-AC5-GPRS EXPANSION MODULE INSTRUCTIONS Important: All Approval and safety information is outlined in the ‘Workabout pro G2 Handheld-computer User Manual’ – part number 8100140A. This manual is available on our website www.psionteklogix.com through the Psion Teklogix community website. Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to meet your specific mobile computing requirements.
PAGE 2
1. Slide the SIM Card holder under the edge of the WORKABOUT PRO case until it meets the inside of the SIM Card slot : Power connector 2. 3. Align the 100-pin expansion connector and the header pins on the expansion module with the expansion connector and the header connector on the main logic board of the WORKABOUT PRO. Align the four mounting tabs on the expansion module with the four screw holes in the internal frame inside the WORKABOUT PRO : 4. 5.
PAGE 3
8. Set the antenna into place. The antenna slides in along the frame. 9. Use the long screw provided to fasten the antenna to the frame 10. Snap the antenna cable onto the antenna • Installing the RFID Module: The RFID Module includes a RFID module UHF-CA3-GPRS (an electronic interface board + RFID Coupler) and RFID circular antenna UHF-AC5.
PAGE 4
1. Remove the screw indicated in the Figure below before inserting the electronic interface board. Remove this screw 2. 3. Set the interface board into place. The interface board slides in along the frame. Use the long screw and the standoff provided to fasten the interface board to the frame. 4. Connect the USB cable of the Interface board on the USB connector of the WAP.
PAGE 5
. Connect the power supply cable of the Interface board on the Power connector of the GPRS Radio module. Then, align the serial cable like in the picture below. Serial cable Power supply cable 6. Power connector Settle the metal shield into place on top of the GSM/GPRS expansion module. It aligns to the same screw holes as the expansion module. Be careful to well align the serial cable and not to pinch the serial cable with the metal shield. And put the end of the serial cable under the plastic.
PAGE 6
7. In a first time use only two screws (M2 x 6 mm) provided to secure the metal shield in place. Put only these two screws at this stage 8. Fix the RFID Coupler into place on the top of the metal shield. The RFID coupler has to be aligned at the centre of the WORKABOUT PRO and respect the following distance from the metal shield : 9.
PAGE 7
10. Connect the RFID Antenna UHF-AC5 to the RFID Coupler. 11. Put the “stopper” and use the two last screws (M2 x 6 mm) provided to secure the module in place. Be careful to the routing of the cable (see the picture below).
PAGE 8
12. Close the extended back plate with the RFID antenna and replace the end-cap.
PAGE 9
• Inserting The SIM Card 1. On the C version of the WORKABOUT PRO, open the card gate in the battery compartment: 2. Remove the sticker covering the SIM Card slot: 3. Slide the SIM Card into the upper slot in the battery compartment: The card should be oriented with the contacts down and the notch to the front and left, according to the diagram in the battery compartment. 4. On the C version of the WORKABOUT PRO, close the card gate.
PAGE 10
• Slide the hardware power switch to turn battery-backup power back on. • Replace the battery and battery cover. For detailed instructions, pleased refer to the WORKABOUT PRO G2 Hand-Held Computer User Manual and to the RFID MODULE UHF-CA3-AC5-GPRS User manual. These manuals are available on our website www.psionteklogix.com through the PSION TEKLOGIX community website. Important: The WORKABOUT PRO G2 with the RFID option must not be held closer than 20 cm from the rest of the body.
PAGE 11
WORKABOUT PRO G2 RFID MODULE UHF-CA3-AC5-GPRS RFID Regulatory Information IMPORTANT NOTE FOR NORTH AMERICA: The RFID must not be used whilst the host WORKABOUT PRO G2 is being powered by the ac/dc adaptor. FCC Information to Users: This product and it antennas must not be co-located or operated in conjunction with any other antenna or transmitter. Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment.