Specifications
Table Of Contents
- Introduction
- Site Preparation and Installation
- Operation and Maintenance
- Problem Isolation
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- PC Keyboard Wedge and USB Keyboard Interfaces
- Connect to a Laptop/No Keyboard Attached
- Send Control/Function Characters - continued
- Caps Lock - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 OF 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements

Product Reference Guide v
RSS Expanded EAN-128 Emulation ......................................................... 5-181
RSS Expanded 2D Component Enable ..................................................... 5-182
RSS Expanded AIM ID .......................................................................... 5-183
RSS Expanded Label ID ........................................................................ 5-184
RSS Expanded Length Control ............................................................... 5-185
RSS Expanded Maximum Label Length .................................................... 5-186
RSS Expanded Minimum Label Length ..................................................... 5-187
RSS Expanded Fixed Length 1 ............................................................... 5-188
RSS Expanded Fixed Length 2 ............................................................... 5-189
Code 39 Enable ......................................................................................... 5-190
Code 39 Start Stop Character Transmission ............................................. 5-191
Code 39 Check Character Calculation ...................................................... 5-192
Code 39 Check Character Transmission ................................................... 5-193
Code 39 Full ASCII ............................................................................... 5-194
Code 39 AIM ID ................................................................................... 5-195
Code 39 Label ID ................................................................................. 5-196
Code 39 Length Control ........................................................................ 5-197
Code 39 Maximum Label Length ............................................................. 5-198
Code 39 Minimum Label Length ............................................................. 5-199
Code 39 Fixed Length 1 ........................................................................ 5-200
Code 39 Fixed Length 2 ........................................................................ 5-201
Code 39 Stitching ................................................................................ 5-202
Pharmacode 39 Enable ............................................................................... 5-203
Pharmacode 39 Start Stop Character Transmission ................................... 5-204
Pharmacode 39 Check Character Transmission ......................................... 5-205
Pharmacode 39 Label ID ....................................................................... 5-206
Code 128 Enable ....................................................................................... 5-207
Code 128 Transmit Function Characters .................................................. 5-208
Convert Code 128 to Code 39 ................................................................ 5-209
Code 128 AIM ID ................................................................................. 5-210
Code 128 Label ID ............................................................................... 5-211
Code 128 Length Control ....................................................................... 5-212
Code 128 Maximum Label Length ........................................................... 5-213
Code 128 Minimum Label Length ............................................................ 5-214
Code 128 Fixed Length 1 ...................................................................... 5-215
Code 128 Fixed Length 2 ...................................................................... 5-216
Code 128 Stitching ............................................................................... 5-217
EAN-128 Enable ........................................................................................ 5-218
EAN 128 AIM ID ................................................................................... 5-219
EAN 128 Label ID ................................................................................. 5-220
Interleaved 2 of 5 (I 2 OF 5) Enable ............................................................. 5-221
I 2 of 5 Check Character Calculation ....................................................... 5-222
I 2 of 5 Check Character Transmission .................................................... 5-223
I 2 of 5 AIM ID .................................................................................... 5-224
I 2 of 5 Label ID .................................................................................. 5-225
I 2 of 5 Length Control ......................................................................... 5-226
I 2 of 5 Maximum Label Length .............................................................. 5-227










