Specifications
Table Of Contents
- Introduction
- Site Preparation and Installation
- Operation and Maintenance
- Problem Isolation
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- PC Keyboard Wedge and USB Keyboard Interfaces
- Connect to a Laptop/No Keyboard Attached
- Send Control/Function Characters - continued
- Caps Lock - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 OF 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements

Product Reference Guide iii
RS-232 Host Echo .................................................................................. 5-71
RS-232 Host Echo Quiet Interval .............................................................. 5-72
RS-232 Ignore Host Commands ............................................................... 5-73
RS-232 TTL ........................................................................................... 5-74
RS-232 TTL Invert ................................................................................. 5-75
RS-232 Beep on ASCII BEL ..................................................................... 5-76
RS-232 Beep on Not on File ..................................................................... 5-77
RS-232 ACK NAK Enable ......................................................................... 5-78
RS-232 ACK Character ............................................................................ 5-80
RS-232 NAK Character ............................................................................ 5-81
RS-232 Retry on ACK NAK Timeout .......................................................... 5-82
RS-232 ACK NAK Timeout Value .............................................................. 5-83
RS-232 ACK NAK Retry Count .................................................................. 5-84
RS-232 ACK NAK Error Handling .............................................................. 5-85
RS-232 Label ID Control ......................................................................... 5-87
Single Cable RS-232 Options ......................................................................... 5-89
Single Cable RS-232 RTS CTS Selection .................................................... 5-90
Single Cable RS-232 Use BCC .................................................................. 5-93
Single Cable RS-232 Use ACK/NAK ........................................................... 5-94
Single Cable RS-232 Use STX .................................................................. 5-95
Set Single Cable RS-232 STX Character .................................................... 5-96
Single Cable RS-232 Use ETX .................................................................. 5-97
Set Single Cable RS-232 ETX Character .................................................... 5-98
PC Keyboard Wedge and USB Keyboard Interfaces ........................................... 5-99
Connect to a Laptop/No Keyboard Attached ............................................. 5-100
Send Control/Function Characters — continued ........................................ 5-102
Caps Lock — continued ......................................................................... 5-104
Country Mode — continued .................................................................... 5-106
Country Mode — continued .................................................................... 5-107
Country Mode — continued .................................................................... 5-108
Country Mode — continued .................................................................... 5-109
Country Mode — continued .................................................................... 5-110
Country Mode — continued .................................................................... 5-111
Keyboard Wedge Intercharacter Delay — continued .................................. 5-113
Keyboard Wedge Intercharacter Delay — continued .................................. 5-114
Keyboard Wedge Intercharacter Delay — continued .................................. 5-115
Quiet Interval — continued .................................................................... 5-117
Quiet Interval — continued .................................................................... 5-118
Quiet Interval — continued .................................................................... 5-119
Symbology Programming ............................................................................ 5-120
UPC-A Enable ............................................................................................ 5-120
UPC-A Number System Character Transmission ........................................ 5-121
UPC-A Check Character Transmission ..................................................... 5-122
Expand UPC-A to EAN-13 ...................................................................... 5-123
UPC/EAN AIM ID .................................................................................. 5-124
UPC-A Label ID .................................................................................... 5-125
UPC-A 2-Digit Supplemental Label ID ...................................................... 5-126










