Specifications
Table Of Contents
- Introduction
- Site Preparation and Installation
- Operation and Maintenance
- Problem Isolation
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- PC Keyboard Wedge and USB Keyboard Interfaces
- Connect to a Laptop/No Keyboard Attached
- Send Control/Function Characters - continued
- Caps Lock - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 OF 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements

ii Magellan
®
2200VS/2200VSΩ and 2300HS/2300HSΩ
Chapter 5. Programming .................................................................................. 5-1
Introduction to Label Programming .................................................................. 5-1
Understanding the Basics ............................................................................... 5-1
Integrating the Scanner With Your Host System ................................................ 5-1
Customizing Your Scanner’s Operation ....................................................... 5-2
Programming Overview .................................................................................. 5-3
Programming via Handheld Device ............................................................. 5-4
What Is Programming Mode? .................................................................... 5-4
Entering and Exiting Programming Mode. .................................................... 5-4
Programming Session .............................................................................. 5-5
LED and Beeper Indicators ............................................................................. 5-9
If You Make a Mistake... ................................................................................. 5-9
Return to Factory Settings ........................................................................ 5-9
Test Mode .............................................................................................5-10
General Scanner Features .............................................................................5-11
Double Read Timeout ..............................................................................5-11
Laser Timeout ........................................................................................5-13
Motor Timeout .......................................................................................5-15
Green LED Idle State ..............................................................................5-18
Scanner Button Options ...........................................................................5-19
Power-up Beep Control ............................................................................5-21
Good Read Beep Control ..........................................................................5-23
Good Read Beep Frequency .....................................................................5-24
Good Read Beep Length ..........................................................................5-26
Good Read Beep Volume .........................................................................5-27
Good Read When to Indicate ....................................................................5-30
EAS Active State ....................................................................................5-32
EAS Timeout ..........................................................................................5-33
Aux Port Mode .......................................................................................5-34
Productivity Index Reporting (PIR) ............................................................5-36
Interface Related Features ............................................................................5-37
Interface Type .......................................................................................5-37
Maximum Host-Transmitted Message Length ..............................................5-51
Number of Host Transmission Buffers ........................................................5-52
Global Prefix ..........................................................................................5-53
Global Suffix ..........................................................................................5-55
IBM Features ...............................................................................................5-57
IBM Transmit Labels in Code 39 Format .....................................................5-57
IBM USB Scanner Device Type .................................................................5-58
RS-232 Features ..........................................................................................5-59
RS-232 Baud Rate ..................................................................................5-59
RS-232 Number of Data Bits ....................................................................5-63
RS-232 Number of Stop Bits ....................................................................5-64
RS-232 Parity ........................................................................................5-65
RS-232 Hardware Control ........................................................................5-67
RS-232 Intercharacter Delay ....................................................................5-69
RS-232 Software Flow Control ..................................................................5-70










