Specifications
Table Of Contents
- Introduction
- Site Preparation and Installation
- Operation and Maintenance
- Problem Isolation
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- PC Keyboard Wedge and USB Keyboard Interfaces
- Connect to a Laptop/No Keyboard Attached
- Send Control/Function Characters - continued
- Caps Lock - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 OF 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements

Product Reference Guide i
Table of Contents
Chapter 1. Introduction .................................................................................... 1-1
Manual Overview ...........................................................................................1-1
How to Use This Manual ............................................................................ 1-2
Scanner Nomenclature ...................................................................................1-3
Connectors ..............................................................................................1-4
Physical Parameters .......................................................................................1-5
Scanning ................................................................................................1-5
AC Adapter .............................................................................................1-5
Electrical Specifications ..................................................................................1-6
Power Supply ..........................................................................................1-7
Laser and Product Safety ................................................................................ 1-8
Labeling ..................................................................................................... 1-10
Agency Compliances .................................................................................... 1-12
Bar Codes Supported ................................................................................... 1-13
Chapter 2. Site Preparation and Installation..................................................... 2-1
Unpacking ....................................................................................................2-1
Operational Verification .................................................................................. 2-2
Installation: Model 2200VS .............................................................................2-3
Installation: Model 2300HS ............................................................................. 2-6
Chapter 3. Operation and Maintenance ............................................................. 3-1
Scanning Items: Model 2200VS ....................................................................... 3-2
Scanning Items: Model 2300HS .......................................................................3-3
Operational Controls ......................................................................................3-4
Operational Modes ......................................................................................... 3-4
Power-Up/Selftest & Pre-Operation .............................................................3-4
Operating Mode ....................................................................................... 3-5
Additional Functions .......................................................................................3-7
Programming ..........................................................................................3-7
Scanner Diagnostic Mode ..........................................................................3-7
Scanner Reset ......................................................................................... 3-8
Operational Maintenance ................................................................................ 3-8
Cleaning .................................................................................................3-8
Chapter 4. Problem Isolation ............................................................................ 4-1
Diagnostic Procedures .................................................................................... 4-2
Error Codes ..................................................................................................4-3
Flowcharts ....................................................................................................4-4










