Specifications
Table Of Contents
- Introduction
- Site Preparation and Installation
- Operation and Maintenance
- Problem Isolation
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- PC Keyboard Wedge and USB Keyboard Interfaces
- Connect to a Laptop/No Keyboard Attached
- Send Control/Function Characters - continued
- Caps Lock - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 OF 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements
Programming
5-248 Magellan
®
2200VS/2200VSΩ and 2300HS/2300HSΩ
Code 93 AIM ID
This feature enables/disables transmission of the Code 93 AIM symbology
identifier.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan your selection from the bar codes below. You’ll need to cover
any unused bar codes on this and the facing page to ensure that the
scanner reads only the bar code you intend to scan.
3. Complete the programming sequence by scanning the SWITCH
bar code.
CODE 93 AIM ID = DISABLE
CODE 93 AIM ID = ENABLE