Specifications
Table Of Contents
- Introduction
- Site Preparation and Installation
- Operation and Maintenance
- Problem Isolation
- Programming
- Introduction to Label Programming
- Understanding the Basics
- Integrating the Scanner With Your Host System
- Programming Overview
- LED and Beeper Indicators
- If You Make a Mistake...
- General Scanner Features
- Interface Related Features
- IBM Features
- RS-232 Features
- RS-232 Baud Rate
- RS-232 Number of Data Bits
- RS-232 Number of Stop Bits
- RS-232 Parity
- RS-232 Hardware Control
- RS-232 Intercharacter Delay
- RS-232 Software Flow Control
- RS-232 Host Echo
- RS-232 Host Echo Quiet Interval
- RS-232 Ignore Host Commands
- RS-232 TTL
- RS-232 TTL Invert
- RS-232 Beep on ASCII BEL
- RS-232 Beep on Not on File
- RS-232 ACK NAK Enable
- RS-232 ACK Character
- RS-232 NAK Character
- RS-232 Retry on ACK NAK Timeout
- RS-232 ACK NAK Timeout Value
- RS-232 ACK NAK Retry Count
- RS-232 ACK NAK Error Handling
- RS-232 Label ID Control
- Single Cable RS-232 Options
- PC Keyboard Wedge and USB Keyboard Interfaces
- Connect to a Laptop/No Keyboard Attached
- Send Control/Function Characters - continued
- Caps Lock - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Country Mode - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Keyboard Wedge Intercharacter Delay - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Quiet Interval - continued
- Symbology Programming
- UPC-A Enable
- UPC-E Enable
- EAN-13 Enable
- EAN-8 Enable
- Other UPC/EAN Options
- GTIN Enable
- RSS-14 Enable
- RSS Expanded Enable
- Code 39 Enable
- Pharmacode 39 Enable
- Code 128 Enable
- EAN-128 Enable
- Interleaved 2 of 5 (I 2 OF 5) Enable
- Codabar Enable
- Codabar Start Stop Character Transmission
- Codabar Start Stop Character Set
- Codabar Start Stop Character Match
- Codabar Check Character Calculation
- Codabar Check Character Transmission
- Codabar AIM ID
- Codabar Label ID
- Codabar Length Control
- Codabar Maximum Label Length
- Codabar Minimum Label Length
- Codabar Fixed Length 1
- Codabar Fixed Length 2
- Codabar Stitching
- Code 93 Enable
- MSI/Plessey Enable
- MSI/Plessey Check Character Calculation
- MSI/Plessey Number of Check Characters
- MSI/Plessey Check Character Transmission
- MSI/Plessey AIM ID
- MSI/Plessey Label ID
- MSI/Plessey Length Control
- MSI/Plessey Maximum Label Length
- MSI/Plessey Minimum Label Length
- MSI/Plessey Fixed Length 1
- MSI/Plessey Fixed Length 2
- MSI/Plessey Stitching
- Standard 2 of 5 Enable
- Standard 2 of 5 Check Character Calculation
- Standard 2 of 5 Check Character Transmission
- Standard 2 of 5 AIM ID
- Standard 2 of 5 Label ID
- Standard 2 of 5 Length Control
- Standard 2 of 5 Maximum Label Length
- Standard 2 of 5 Minimum Label Length
- Standard 2 of 5 Fixed Length 1
- Standard 2 of 5 Fixed Length 2
- Standard 2 of 5 Stitching
- LED/Beeper Indications & Controls
- Cable Information
- Keypad
- Host Commands
- Factory Defaults
- Handheld Data Format Requirements
Programming
5-186 Magellan
®
2200VS/2200VSΩ and 2300HS/2300HSΩ
RSS Expanded Maximum Label Length
This feature specifies the maximum allowable length of an RSS Expanded
label.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan the bar code,
SET RSS EXPANDED MAXIMUM LABEL
LENGTH
below. You’ll need to cover any unused bar codes on this
and the facing page to ensure that the scanner reads only the bar
code you intend to scan.
3. Scan the appropriate digits from the keypad in
Appendix C that rep-
resent the desired maximum label length. The selectable range for
this option is 00 to 74. Pad all single digit numbers with a leading
zero to yield a two-digit entry (00-74).
4. Complete the programming sequence by scanning the SWITCH
bar code.
SET RSS EXPANDED MAXIMUM LABEL LENGTH
NOTE
Length in this case includes check and data characters. This applies
when RSS Expanded Length Control is set to variable-length decod-
ing.
Maximum Label Length should be greater than or equal to Minimum
Label Length.