Installation Manual

Table of Contents
Section I GENERAL INFORMATION ................................................................................................................................................... 1-1
1.1 INTRODUCTION ............................................................................................................................................................................ 1-1
1.2 SCOPE ............................................................................................................................................................................................... 1-1
1.3 EQUIPMENT DESCRIPTION ...................................................................................................................................................... 1-1
1.4 APPROVAL BASIS – FAA TSO C35D .......................................................................................................................................... 1-1
1.5 SPECIFICATIONS .......................................................................................................................................................................... 1-1
1.6 EQUIPMENT SUPPLIED .............................................................................................................................................................. 1-2
1.7 EQUIPMENT REQUIRED BUT NOT SUPPLIED .................................................................................................................... 1-2
1.8 LICENSE REQUIREMENTS ........................................................................................................................................................ 1-2
Section II - Installation............................................................................................................................................................................... 2-1
2.1 GENERAL INFORMATION ......................................................................................................................................................... 2-1
2.1.1 SCOPE ........................................................................................................................................................................................... 2-1
2.1.2 CERTIFICATION REQUIREMENTS.................................................................................................................................................... 2-1
2.2 UNPACKING AND PRELIMINARY INSPECTION ............................................................................................................................... 2-1
2.3 EQUIPMENT INSTALLATION PROCEDURES .................................................................................................................................... 2-1
2.3.1 COOLING REQUIREMENTS.............................................................................................................................................................. 2-1
2.3.2 MOUNTING REQUIREMENTS .......................................................................................................................................................... 2-1
2.3.3 CONNECTOR ASSEMBLY ................................................................................................................................................................ 2-1
2.4 CABLE HARNESS WIRING................................................................................................................................................................. 2-2
2.4.1 POWER ............................................................................................................................................................................................ 2-2
2.4.2 AUDIO PANEL INTERFACE .............................................................................................................................................................. 2-2
2.4.3 LAMP DIMMING.............................................................................................................................................................................. 2-2
2.4.4 MARKER ANTENNA INSTALLATION............................................................................................................................................... 2-2
2.4.5 EXTERNAL MARKER LIGHTS ......................................................................................................................................................... 2-2
2.4.6 REMOTE MODE SELECTOR- MB10R VERSION ONLY ................................................................................................................... 2-2
2.4.7 MIDDLE MARKER SENSE ............................................................................................................................................................... 2-3
2.5 ADJUSTMENTS ................................................................................................................................................................................... 2-3
2.6 MB10 PIN ASSIGNMENTS.................................................................................................................................................................. 2-3
2.7 UNIT INSTALLATION ......................................................................................................................................................................... 2-3
2.7.1 PANEL INSTALLATION .................................................................................................................................................................... 2-3
2.7.2 REMOTE INSTALLATION ................................................................................................................................................................. 2-4
2.8 POST INSTALLATION CHECKOUT.................................................................................................................................................... 2-4
2.9 OPERATIONAL CHECKOUT .............................................................................................................................................................. 2-4
2.9.1 REQUIRED TEST EQUIPMENT......................................................................................................................................................... 2-4
2.9.2 MARKER CHECKOUT...................................................................................................................................................................... 2-4
2.10 FINAL INSPECTION ......................................................................................................................................................................... 2-4
Section III OPERATION .......................................................................................................................................................................... 3-1
3.1 SCOPE ............................................................................................................................................................................................... 3-1
3.2 POWER ................................................................................................................................................................................................ 3-1
3.3 MARKER BEACON OPERATION ....................................................................................................................................................... 3-1
Section IV- Warranty and Service............................................................................................................................................................. 4-1
4.1 WARRANTY ........................................................................................................................................................................................ 4-1
4.2 FACTORY SERVICE............................................................................................................................................................................ 4-1
Appendix A – MB10 Installation Drawings ................................................................................................................................................A
Appendix B, J10 Interconnect ......................................................................................................................................................................B
Appendix C- Instructions for FAA Form 337 and continuing airworthiness...............................................................................................C
7.1 INSTRUCTIONS FOR FAA FORM 337..................................................................................................................................................C
7.2 INSTRUCTIONS FOR CONTINUING AIRWORTHINESS, AUDIO SYSTEM ..........................................................................................C
Appendix D RTCA DO160E Environmental Qualification Form..............................................................................................................D
Rev Date Change
1 5-22-07 Updated to add remote version
2 8-14-07 Update to show TSO information
3 11-12-07 Clarified dimming information, sections 2.4.3, 2.4.5, 2.4.6
4 1-9-08 Added drawing for remote installation to Appendix A
5 1-16-08 Clarified CB size and antenna connector
6 3-12-08 Corrected dimension to show overall width §1.5
7 4-16-09 Corrected page number and Advisory Circular references.
8 10-3-12 Added additional dimmer information §3.4.3
9 9-3-13 Clarified mounting hole locations