9800 Martel Road Lenoir City, TN 37772 IntelliPAX Intercom Expansion Unit Unit Part Numbers 11606, 11606R for use with PMA7000-Series and PAC24 11616, 11616R for use with other intercom systems 11626 11626R for use with PM1000-DAP 11606-SA Stand Alone Cabin Intercom 11636R for use with PMA8000D Passenger Intercom System Installation and Operation Manual US Patent No. 6,493,450 Document P/N 200-250-0005 Revision 14, January 2012 PS Engineering, Inc.
PS Engineering, Inc. IntelliPAX Expansion Unit the Publications Manager at PS Engineering, Inc., 9800 Martel Road, Lenoir City, TN 37772. Phone (865) 988-9800 www.ps-engineering.com Table of Contents SECTION I – GENERAL INFORMATION 1.1 INTRODUCTION 1.2 SCOPE 1.3 DESCRIPTION 1.4 APPROVAL BASIS 1.5 SPECIFICATIONS 1.6 EQUIPMENT REQUIRED BUT NOT SUPPLIED 1-1 1-1 1-1 1-1 1-1 1-2 1-2 SECTION II – INSTALLATION 2.1 GENERAL INFORMATION 2.2 UNPACKING AND PRELIMINARY INSPECTION 2.
PS Engineering, Inc. IntelliPAX Expansion Unit Section I – General Information 1.1 Introduction The IntelliPAX is a panel mounted, multi-place intercom expansion unit used to add up to six extra stations to an intercom system. Please read this manual completely before installation to minimize the risk of damage to the unit and to become familiar with all the features. 1.
PS Engineering, Inc. IntelliPAX Expansion Unit 1.5 Specifications Input power: Headphone Impedance: Audio Distortion: Aircraft Radio Impedance: 3 dB Mic Frequency Response: 3 dB Music Frequency Response: Unit weight: Dimensions: 1.6 A. B. C. D. E. from main unit 150-1000 typical <10% @ 35 mW into 150 load 1000 typical 350 Hz — 6000 Hz 200 Hz to 15 kHz 7.2 Ounces (0.20 kg) 1.25" H x 3.00" W x 5.50" D (3.2 x 6.
PS Engineering, Inc. IntelliPAX Expansion Unit Section II – Installation 2.1 General Information The IntelliPAX comes with all necessary hardware for a typical installation. The unit is installed either in the panel (11606, 11616, 11626) or mounted blindly (11606R, 11616R or 11626R). If panel mounted, it can be installed near the main unit, or near the passengers. If blind mounted, it can be mounted nearly anywhere.
PS Engineering, Inc. IntelliPAX Expansion Unit 2.3 Equipment installation procedures 2.40” 2 ea. 0.125 NOT TO SCALE For panel mounted installation (11606, 11616, 11626) 1. Using the template, drill three holes in the instrument panel in a location convenient to the pilot or passengers position(s). 2. Insert the IntelliPAX from behind the instrument panel, aligning the holes for the knobs. 3. Place the aluminum faceplate over the knob shaft and secure, using the two # 4-40 round head screws provided. 4.
PS Engineering, Inc. IntelliPAX Expansion Unit 2.4.2 Power Requirements The IntelliPAX was designed to work with the main intercom unit. No other power is required. The Stand Alone unit is connected to a 1A breaker to the avionics bus (2A for dual). 2.4.3 Interconnection with main unit Interface between the IntelliPAX and the main intercom is through a 4-wire shielded cable.
PS Engineering, Inc. IntelliPAX Expansion Unit Section III – OPERATION 3.1 Power Switching on the intercom or audio panel automatically activates the IntelliPAX unit. The Stand Alone unit is active when power is applied to the Avionics Bus. 3.2 Adjusting the Volume For the P/N 11606R, operating with a PMA7000B or copilot’s PMA8000D, the audio panel’s Passenger volume control (PASS) affects the expansion intercom volume.
PS Engineering, Inc. IntelliPAX Expansion Unit Section IV Warranty and Service 4.1 Warranty In order for the factory warranty to be valid, the installations in a certified aircraft must be accomplished by a FAA- certified avionics shop and authorized PS Engineering dealer. If the unit is being installed by a non-certified individual in an experimental aircraft, a factory-made harness must be used for the warranty to be valid. PS Engineering, Inc.
PS Engineering, Inc. IntelliPAX Expansion Unit Appendix A Instructions for FAA Form 337 and Airworthiness 5.1 Sample text for FAA Form 337 One method of airworthiness approval is through an FAA Form 337, Major Repair and Alteration (Airframe, Powerplant, Propeller, or Appliance) In the case of the IntelliPAX part number 116( ), you may use the following text as a guide. Installed intercom expansion unit, PS Engineering IntelliPAX, part number 11616 in ( location ) at station . Installed per AC43.
PS Engineering, Inc. IntelliPAX Expansion Unit Appendix B Installation 5.480 A Ø0.136 4.000 3.500 A A 4.725 Figure 6-1 Remote unit outline 200-250-0005 Page B Rev. 14, Jan.
PS Engineering, Inc.
PS Engineering, Inc.
PS Engineering, Inc.
