Portable Generator User Manual

ManualsBrandsPS Audio ManualsPortable GeneratorP1000

Table of Contents

1. What’s in the Box

2. Warning

2. Safety Instruction

2. Overview

3. Quick Start Guide

4. Rear Panel Layout

4. Front Panel Controls

4. Display Modes

6. Additional Display Notifications

6. Setup Display Mode

8. Servo System

9. MultiWave II

10. Troubleshooting Guide

11. Specifications

11. Warranty and Service

12. Contact Information

What’s in the Box

• One Power Plant P1000

• One 6 foot AC power cable

• One user’s manual

• One warranty card

• One spare 1 amp fast blow fuse

• One spare 15 amp slow blow fuse

IMPORTANT:

Be sure to save all packing materials included

with the Power Plant P1000 as this will be

required if you ever need to ship the unit for ser-

vice or modification.

PS Audio International, Inc.

4824 Sterling Dr.

Boulder, CO 80301 USA

Toll Free: 877-772-8340

Ph: 720-406-8946

Fax: 720-406-8967

www.psaudio.com

Summary of content (6 pages)

PAGE 1
Table of Contents PS Audio International, Inc. 4824 Sterling Dr. Boulder, CO 80301 USA Toll Free: 877-772-8340 Ph: 720-406-8946 Fax: 720-406-8967 www.psaudio.com 12 1. 2. 2. 2. 3. 4. 4. 4. 6. 6. 8. 9. 10. 11. 11. 12.
PAGE 2
Warning Overview To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the enclosure. Refer servicing to qualified personnel only. The Power Plant P1000 is a power regenerator capable of delivering the highest level of AC performance to all audio and video components. The PS Audio Power Plant P1000 is designed To prevent electric shock, use a 3 prong, to operate as a stand-alone power management grounded type power cable.
PAGE 3
up the P1000. If the Filtered AC outlets still do not P1000 is being overworked. pass AC, please contact your dealer for additional service. The display is flashing a percentage The P1000 will turn itself off and flash a percentThe P1000 seems to be working, but the dis- age (for example, “184%”) on the display if it play is blank detects an over-current condition. The P1000 may be in the display blanking mode.
PAGE 4
Troubleshooting Guide [AUTO] AutoWave This revolutionary new process automatically computes the best MultiWave II setting for a particular power load as presented by the connected equipment. The beauty of this system is its ability to instantly change the power setting of the AC regenerator with the dynamic load variations the equipment presents. The Power Plant P1000 sets a new mark for performance and protection. It has been designed to bring forth the absolute best from the connected equipment.
PAGE 5
MultiWave II [MWAV2] MultiWave2 MultiWave2 is a 60Hz SineWave that incorporates a pseudorandom collection of frequencies which are dithered from 55-65Hz. MultiWave II is a technology available exclusively on the newest PS Audio Power Plant series of AC Regenerators. The P1000 includes MultiWave II and also features AutoWave and TubeWave. There are 4 MultiWave II waveforms as well as TubeWave, AutoWave and SineWave mode. MultiWave II is only available at the Regenerated AC outlets.
PAGE 6
Additional Display Notifications • 100 volt model ranges from 95 - 105 v Default setting is 100 volts. • 120 volt model ranges from 100 - 120 v Default setting is 117 volts. • 240 volt model ranges from 220 - 240 v Default setting is 240 volts. (adjustments in 2 volt increments) HOT! - If the P1000 exceeds safe operating temperature the front panel display will flash “HOT!”. The Regenerated AC outlets will stop generating AC until the P1000 returns to safe operating temperature.