Installation and Operation Guide
Table Of Contents
- Chapter 1: Introduction
- 1.1 First steps
- 1.2 Service addresses
- 1.3 About this manual
- Chapter 2: Safety
- 2.1 Safety symbols
- 2.2 Information for the system operator
- 2.3 Information for operating personnel
- 2.4 Intended use
- 2.5 Residual risks and safety measures
- Declaration of conformity
- Certifications
- Chapter 3: Technical data
- Chapter 4: System description
- 4.1 VIBCONNECT RF bridge
- 4.2 VIBCONNECT RF sensor unit
- 4.3 VIBCONNECT RF sensor
- Chapter 5: Installation & commissioning
- 5.1 Quick guide
- 5.2 Configuration in OMNITREND
- 5.3 Installation & commissioning of bridge
- 5.4 Installation & commissioning of sensor unit
- 5.5 Installation of sensors
- 5.6 Configuration in OMNITREND (continued)
- 5.7 Installing additional sensor unit
- Chapter 6: Maintenance
- 6.1 Cleaning
- 6.2 System time correction
- 6.3 Installation report
- 6.4 Battery-powered sensor unit
- 6.5 Update
- 6.6 Warranty
- 6.7 Spare parts and accessories
- Chapter 7: Troubleshooting
- Chapter 8: After use
16
VIBCONNECT RF 05.2012
TCB
GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:
ACB, Inc.
6731 Whittier Avenue Suite C110
McLean, VA 22101
Date of Grant: 02/26/2014
Application Dated: 02/25/2014
PRÜFTECHNIK Condition Monitoring GmbH
Oskar-Messter-Str. 19-21
Ismaning, 85737
Germany
Attention:Horst Göhlich , Dr.
NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the nam
ed GRANTEE,
and is VALID ONLY for the equipment identified here
on for use under the
Commission's Rules and Regulations listed below.
FCC IDENTIFIER:
CHO-VCRFSU24
NameofGrantee:
PRÜFTECHNIK Condition
Monitoring GmbH
EquipmentClass: Digital Transmission System
Notes: VIB CONNECT RF Sensor Unit /
Industrial Data Acquisition System
Grant Notes
FCC Rule Parts
Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
15C 2435.2 - 2435.2 0.00186
Power output listed is conducted. This transmitter
must not be co-located with any
other transmitters except in accordance with FCC mu
lti-transmitter product
procedures. End-users must be provided with antenna
installation instructions and
transmitter operating conditions for satisfying RF
exposure compliance.
TCB
GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:
ACB, Inc.
6731 Whittier Avenue Suite C110
McLean, VA 22101
Date of Grant: 03/06/2014
Application Dated: 03/06/2014
PRÜFTECHNIK Condition Monitoring GmbH
Oskar-Messter-Str. 19-21
Ismaning, 85737
Germany
Attention:Horst Göhlich , Dr.
NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the nam
ed GRANTEE,
and is VALID ONLY for the equipment identified here
on for use under the
Commission's Rules and Regulations listed below.
FCC IDENTIFIER:
CHO-VCRFBR24
NameofGrantee:
PRÜFTECHNIK Condition
Monitoring GmbH
EquipmentClass: Digital Transmission System
Notes: VIB CONNECT RF Bridge / Industrial
Data Acquisition System
Grant Notes
FCC Rule Parts
Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
15C 2434.9 - 2434.9 0.00171
Power output listed is conducted. This transmitter
must not be co-located with any
other transmitters except in accordance with FCC mu
lti-transmitter product
procedures. End-users must be provided with antenna
installation instructions and
transmitter operating conditions for satisfying RF
exposure compliance.