User Manual and Installation Guide Proxy Mobile Reader Pro Wallbox www.proxy.com | support@proxy.
| 2
Table of Contents Introduction 5 Reader Functionality Mobile Reader Pro Wallbox Main Housing Mobile Reader Pro Wallbox Wall Plate Product Details RF Exposure Information 5 5 6 6 7 7 Reader Specifications Rated current at different operating voltages for PRXY-WW-1.0 & PRXY-WK-1.
CE Tune up power table BLE / WLAN Waste Electrical and Electronic Equipment (WEEE) UL294 UL 294 Access Control Performance Levels | 4 15 15 16 16 16
Introduction This document details the Proxy Mobile Reader Pro and its basic operational and installation procedures. It covers the details of the Wallbox form-factor reader. Model: Standard Wallbox PRXY-WW-1.0 (white version) , PRXY-WK-1.0 (black version) The reader comes in one variant for interfacing with the control panel. ● Standard HF LF BLE IEEE 802.11b/g/n The reader comes in one variant in functionality. ● Standard HF LF BLE IEEE 802.
Mobile Reader Pro Wallbox Main Housing Mobile Reader Pro Wallbox Wall Plate | 6
Product Details Model Name: Standard Wallbox / PRXY-WW-1.0 / PRXY-WK-1.0 Device Type: RFID reader, 13.56MHz (HF) / 125 KHz (LF) / Mobile Credential: 2.4GHz (BLE) Physical Access control Reader (accessory equipment) Type of Equipment: Sealed Reader Suitable for Indoor use and Outdoor use – PRXY-MW-1.0 and PRXY-MK-1.0 Interface Type: Pigtail Cable (11 Core + Drain) Electrical Rating: 6V - 16V DC, 0.5A, 8W (Max) Communication Protocol: Wiegand, RS485 (2wire - Half Duplex), BLE, IEEE 802.
Reader Specifications Model Operating Voltage PRXY-WW-1.0 // PRXY-WK-1.0 HF LF BLE IEEE 802.11b Current Rating 6V - 16V DC Operating Temperature -35C to +66C, 85% RH 0.5A There shall be no connections made to the RS-485 interface (RS485+ and RS485-) for UL installations. Note: ● Standby Power is not provided by the Card Readers. The Standby Power Level is dependent on the external power source connected to the Card Reader.
Installation Details Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction. Parts List ● Mobile Reader Pro - 1 ● Security Screw – #6 - 32 x 3/8” -- 1 Nos ● Mounting Screws - #6-32 x 1” -- 2 Nos ● Nylon anchor plugs - #6 Size x 1” -- 2 Nos Recommended Infrastructure ● All cabling and wiring shall be UL Listed and/or UL Recognized.
Wiring Information Cable Color codes for Pig Tail Reader Red +VDC 12V (nominal) Black & White Ground Green Wiegand Data 0 White Wiegand Data 1 Orange Green LED Yellow Buzzer Blue Hold Brown Red LED Grey RS485 - Pink RS485 + Violet Tamper Output Black / Drain Shield Ground N, ** For Wiring diagrams and termination points please see your control panel user manual. Installations will differ between access control panel manufacturers.
Mounting the Mobile Reader Pro Location of mounting holes on wall: Reader Installation Steps | 11 ● Make two holes on the wall as per the image above corresponding to the type of reader. ● Insert the nylon screw plugs into the wall. ● Connect the wires as per the Table in Section 5.3.1. ● Mobile Reader Pro Wallbox Wall Plate is to be secured onto the wall using the Screws (A). ● Mobile Reader Pro Wallbox Main Housing can be installed onto Wall Plate.
Power Up and Testing 1. Turn power on. 2. ● Indicator Light (top of housing) powers on and turns RED. ● Branding LEDs turn on (Proxy Logo Displayed). Present a card. ● Access Granted: The Indicator LED blinks green, and a short beep is emitted. ● Access Denied: This is dependent on Access controller configuration. 3. Present a Phone with Proxy ID App Enabled. ● Access Granted: The Indicator LED blinks green, and a short beep is emitted.
Certifications FCC Tune up power table BLE / WLAN ● Each product is programmed with the pre-defined RF parameters. ● Each product RF power level is measured to ensure the power level not exceeding the target power level, in a fully calibrated setup. ● These settings cannot be changed. Please find below the Maximum Transmit Power for production units: Band / Mode Average Power (dBm) LE GFSK Bluetooth 7 Band / Channel / Frequency (MHz) 2.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
RF Exposure Information This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Informations d’exposition RF Cet appareil a été testé et répond aux limites applicables en matière d’exposition aux radiofréquences (RF). Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
Hereby, Proxy, Inc. declares that the radio equipment type Mobile Reader Pro is in compliance with Directive 2014/53/EU. Please scan the barcode on the label to view the user guide. Waste Electrical and Electronic Equipment (WEEE) This symbol means that according to local laws and regulations your product and/or its battery shall be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities.
