User guide
Table Of Contents
- Introduction
- Installation and Initialization
- System Status
- Advanced Configuration
- System
- Network
- Interfaces
- Management
- Filtering
- Alarms
- Bridge
- QoS
- Radius Profiles
- SSID/VLAN/Security
- Monitoring
- Commands
- Troubleshooting
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables and Strings
- Configuring the AP using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Set System Name, Location and Contact Information
- Set Static IP Address for the AP
- Change Passwords
- Set Network Names for the Wireless Interface
- Enable 802.11d Support and Set the Country Code
- Enable and Configure TX Power Control for the Wireless Interface
- Configure SSIDs (Network Names), VLANs, and Profiles
- Download an AP Configuration File from your TFTP Server
- Backup your AP Configuration File
- Set up Auto Configuration
- Other Network Settings
- Configure the AP as a DHCP Server
- Configure the DNS Client
- Configure DHCP Relay
- Configure DHCP Relay Servers
- Maintain Client Connections using Link Integrity
- Change Wireless Interface Settings
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure Wireless Distribution System
- Configure MAC Access Control
- Set RADIUS Parameters
- Set Rogue Scan Parameters
- Set Hardware Configuration Reset Parameters
- Set VLAN/SSID Parameters
- Set Security Profile Parameters
- CLI Monitoring Parameters
- Parameter Tables
- CLI Batch File
- ASCII Character Chart
- Specifications
- Technical Services and Support
- Statement of Warranty
Advanced Configuration AP-700 User Guide
Interfaces
47
• 802.11b/g mode: This is the default mode. Use this mode if you want to support a mix of 802.11b and 802.11g
devices.
• 802.11g-wifi mode: The 802.11g-wifi mode has been defined for Wi-Fi testing purposes. It is not recommended for
use in your wireless network environment.
NOTE: In countries in which 802.11a (5 GHz) is not available for use, the AP-700 provides dual-band (802.11b and
802.11g) support only. 802.11a functionality covered in this User Guide is not supported.
Super Mode and Turbo Mode
Super mode improves throughput between the access point and wireless clients that support this capability. For wireless
clients that support this capability the AP will negotiate and treat them accordingly, for other clients that do not support
super mode, the AP will treat them as normal wireless clients.
Super mode can be configured only when the wireless operational mode is one of the following:
• 802.11a only mode
• 802.11g only mode
• 802.11b/g mode
NOTE: Super mode is not available in 802.11b and 802.11g-wifi operational modes. Turbo mode is available only in
802.11a mode in the FCC regulatory domain.
Turbo mode is supported in 802.11a mode in the FCC regulatory domain. Turbo mode supports turbo speeds at twice the
standard data rates, and also dynamically switches between Turbo mode speeds and normal speeds depending on the
wireless client. All connected clients must be using Turbo mode in order for the AP to operate at Turbo mode speed. If
turbo mode is enabled, then this is displayed in the web UI and the transmit speeds and channels pull-down menus are
updated with the valid values.
When Turbo mode is enabled, only a subset of the wireless channels in the 5.0 GHz spectrum can be used. If any
wireless clients do not support turbo mode, the AP will fall back to normal mode.
Turbo mode can be configured only when Super mode has already been enabled.
Super mode is supported in the 2.4 GHz and 5 GHz frequency bands in all regulatory domains. Turbo mode is available
in the 5 GHz frequency band in the FCC regulatory domain.
IEEE 802.11d Support for Additional Regulatory Domains
The IEEE 802.11d specification allows conforming equipment to operate in more than one regulatory domain over time.
IEEE 802.11d support allows the AP to broadcast its radio’s regulatory domain information in its beacon and probe
responses to clients. This allows clients to passively learn what country they are in and only transmit in the allowable
spectrum. When a client enters a regulatory domain, it passively scans to learn at least one valid channel, i.e., a channel
upon which it detects IEEE Standard 802.11 frames.
The beacon frame contains information on the country code, the maximum allowable transmit power, and the channels to
be used for the regulatory domain.
The same information is transmitted in probe response frames in response to a client’s probe requests. Once the client
has acquired the information required to meet the transmit requirements of the regulatory domain, it configures itself for
operation in the regulatory domain.
On some AP models, the regulatory domain and associated parameters are automatically configured when a country is
selected on the System tab. On APs in which country selection is not available on the system tab, the regulatory domain
is pre-programmed into the AP prior to shipment. Depending on the regulatory domain, a default country code is chosen
that is transmitted in the beacon and probe response frames.
Configuring 802.11d Support
Perform the following procedure to enable 802.11d support and select the country code: