User guide
Table Of Contents
- Introduction
- Installation and Initialization
- System Status
- Advanced Configuration
- System
- Network
- Interfaces
- Management
- Filtering
- Alarms
- Bridge
- QoS
- Radius Profiles
- SSID/VLAN/Security
- Monitoring
- Commands
- Troubleshooting
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables and Strings
- Configuring the AP using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Set System Name, Location and Contact Information
- Set Static IP Address for the AP
- Change Passwords
- Set Network Names for the Wireless Interface
- Enable 802.11d Support and Set the Country Code
- Enable and Configure TX Power Control for the Wireless Interface
- Configure SSIDs (Network Names), VLANs, and Profiles
- Download an AP Configuration File from your TFTP Server
- Backup your AP Configuration File
- Set up Auto Configuration
- Other Network Settings
- Configure the AP as a DHCP Server
- Configure the DNS Client
- Configure DHCP Relay
- Configure DHCP Relay Servers
- Maintain Client Connections using Link Integrity
- Change Wireless Interface Settings
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure Wireless Distribution System
- Configure MAC Access Control
- Set RADIUS Parameters
- Set Rogue Scan Parameters
- Set Hardware Configuration Reset Parameters
- Set VLAN/SSID Parameters
- Set Security Profile Parameters
- CLI Monitoring Parameters
- Parameter Tables
- CLI Batch File
- ASCII Character Chart
- Specifications
- Technical Services and Support
- Statement of Warranty
Command Line Interface (CLI) AP-700 User Guide
Parameter Tables
196
Interface Parameters
Wireless Interface Parameters
The wireless interface group parameter is wif. The wireless interface uses table index 3.
Common Parameters to 802.11a and 802.11b/g
* For 802.11a APs certified in the ETSI and TELEC regulatory domains and operating in the middle frequency band, disabling Auto Channel
Select will limit the available channels to those in the lower frequency band.
† Wireless Service Status cannot be shut down on an interface where Rogue Scan is enabled.
‡ Distance Between APs allows the AP to perform better in high noise environments by increasing the receive sensitivity and transmit defer
threshold, as follows:
Name Type Value Access CLI Parameter
Wireless Interfaces Group N/A R wif
Table Index Integer 3 R index
Operational Mode Integer 1 = dot11b-only
2 = dot11g-only
3 = dot11bg
4 = dot11a
5 = dot11g-wifi
RW mode
Network Name DisplayString 1 - 32 characters
My Wireless Network (default)
RW netname
Auto Channel Select
(ACS)*
Integer enable (default)
disable
RW autochannel
DTIM Period Integer 1 - 255
1 = default
RW dtimperiod
RTS/CTS Medium
Reservation
Integer 0 - 2347
Default is 2347 (off)
RW medres
MAC Address PhyAddress 12 hex digits R macaddr
Wireless Service Status
†
Integer 1 = resume
2 = shutdown
RW wssstatus
Supported Frequency
Channels
Octet String Depends on Regulatory Domain R suppchannels
Load Balancing Max
Clients
Integer 1 - 63 RW lbmaxclients
Distance Between APs
‡
Integer 1 (large) (default)
2 (medium)
3 (small)
4 (minicell)
5 (microcell)
RW distaps
Transmit Power Control Integer enable
disable
RW txpowercontrol
Transmit Power Control
Back-Off
Integer 0 - 35 (dBm) RW currentbackofftpcvalue
Antenna Diversity Integer 1 (Antenna 1)
2 (Antenna 2)
5 (Auto; both antennas)
(See Configure Antenna Diversity)
RW atdiversity
Distance Between
APs
Receive Sensitivity
Threshold (dBm)
Transmit Defer Threshold
(dBm)
Large -96 -62