User guide
Table Of Contents
- Introduction
- Installation and Initialization
- System Status
- Advanced Configuration
- System
- Network
- Interfaces
- Management
- Filtering
- Alarms
- Bridge
- QoS
- Radius Profiles
- SSID/VLAN/Security
- Monitoring
- Commands
- Troubleshooting
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables and Strings
- Configuring the AP using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Set System Name, Location and Contact Information
- Set Static IP Address for the AP
- Change Passwords
- Set Network Names for the Wireless Interface
- Enable 802.11d Support and Set the Country Code
- Enable and Configure TX Power Control for the Wireless Interface
- Configure SSIDs (Network Names), VLANs, and Profiles
- Download an AP Configuration File from your TFTP Server
- Backup your AP Configuration File
- Set up Auto Configuration
- Other Network Settings
- Configure the AP as a DHCP Server
- Configure the DNS Client
- Configure DHCP Relay
- Configure DHCP Relay Servers
- Maintain Client Connections using Link Integrity
- Change Wireless Interface Settings
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure Wireless Distribution System
- Configure MAC Access Control
- Set RADIUS Parameters
- Set Rogue Scan Parameters
- Set Hardware Configuration Reset Parameters
- Set VLAN/SSID Parameters
- Set Security Profile Parameters
- CLI Monitoring Parameters
- Parameter Tables
- CLI Batch File
- ASCII Character Chart
- Specifications
- Technical Services and Support
- Statement of Warranty
Command Line Interface (CLI) AP-700 User Guide
Parameter Tables
188
Parameter Tables
Objects contain groups that contain both parameters and parameter tables. Use the following Tables to configure the
Access Point. Columns used on the tables include:
• Name - Parameter, Group, or Table Name
• Type - Data type
• Value - Value range, and default value, if any
• Access = access type, R = Read Only (show), RW = Read-Write (can be “set”), W = Write Only
• CLI Parameter - Parameter name as used in the Access Point
Access Point network objects are associated with Groups. The network objects are listed below and associated
parameters are described in the following Parameter Tables:
• System Parameters - Access Point system information
– Inventory Management Information - Hardware, firmware, and software version information
• Network Parameters - IP and Network Settings
– IP Configuration Parameters - Configure the Access Point’s IP settings
• DNS Client for RADIUS Name Resolution - Configure the Access Point as a DNS client
– DHCP Server Parameters - Enable or disable dynamic host configuration
– SNTP Parameters - Configure
– Link Integrity Parameters - Monitor link status
• Interface Parameters - Configure Wireless and Ethernet settings
– Wireless Interface Parameters
• Wireless Distribution System (WDS) Parameters - Configure the WDS partnerships
– Wireless Interface SSID/VLAN/Profile Parameters - Configure the SSIDs, VLANs, and security modes. Up to 16
SSIDs are supported; different security settings can be applied to each SSID, and a unique VLAN can be
configured per SSID.
– Ethernet Interface Parameters - Set the speed and duplex of the Ethernet port.
• Management Parameters - Control access to the AP’s management interfaces
– SNMP Parameters - Set read and read/write passwords
– HTTP Parameters - Set up the graphical web browser interface. If required, enable SSL and configure the SSL
certificate passphrase.
– Telnet Parameters - Telnet Port setup
– Serial Port Parameters - Serial Port setup
– RADIUS Based Management Access Parameters - Configure RADIUS Based Management Access for HTTP and
Telnet access.
– SSH Parameters - Enable SSH and configure the host key.
– TFTP Server Parameters - Set up for file transfers; specify IP Address, file name, and file type
– IP Access Table Parameters - Configure range of IP addresses that can access the AP
– Auto Configuration Parameters - Configure the Auto Configuration feature which allows an AP to be automatically
configured by downloading a configuration file from a TFTP server during boot up.
• Filtering Parameters
– Ethernet Protocol Filtering Parameters - Control network traffic based on protocol type
– Static MAC Address Filter Table - Enable and disable specific addresses
– Proxy ARP Parameters - Enable or disable proxy ARP for wireless clients
–
IP ARP Filtering Parameters - Control which ARP messages are sent to wireless clients based on IP settings
– Broadcast Filtering Table - Control the type of broadcast packets forwarded to the wireless network