Access Point User Guide
Table Of Contents
- Introduction
- Installation and Initialization
- System Status
- Advanced Configuration
- System
- Network
- Interfaces
- Management
- Filtering
- Alarms
- Bridge
- QoS
- Radius Profiles
- SSID/VLAN/Security
- Monitoring
- Commands
- Troubleshooting
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables and Strings
- Configuring the AP using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Set System Name, Location and Contact Information
- Set Static IP Address for the AP
- Change Passwords
- Set Network Names for the Wireless Interface
- Enable 802.11d Support and Set the Country Code
- Enable and Configure TX Power Control for the Wireless Interface(s)
- Configure SSIDs (Network Names), VLANs, and Profiles
- Download an AP Configuration File from your TFTP Server
- Backup your AP Configuration File
- Set up Auto Configuration
- Other Network Settings
- Configure the AP as a DHCP Server
- Configure the DNS Client
- Configure DHCP Relay
- Configure DHCP Relay Servers
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure Wireless Distribution System
- Configure MAC Access Control
- Set RADIUS Parameters
- Set Rogue Scan Parameters
- Set Hardware Configuration Reset Parameters
- Set VLAN/SSID Parameters
- Set Security Profile Parameters
- CLI Monitoring Parameters
- Parameter Tables
- CLI Batch File
- ASCII Character Chart
- Specifications
- Technical Support
- Statement of Warranty
- Regulatory Compliance
Advanced Configuration AP-4000 Series User Guide
Management
68
Management
The Management tab contains the following sub-tabs:
• Passwords
• IP Access Table
• Services
• Automatic Configuration (AutoConfig)
• Hardware Configuration Reset (CHRD)
Passwords
You can configure the following passwords:
• SNMP Read Community Password: The password for read access to the AP using SNMP. Enter a password in both
the Password field and the Confirm field. This password must be between 6 and 32 characters. The default
password is “public”.
• SNMP Read/Write Community Password: The password for read and write access to the AP using SNMP. Enter a
password in both the Password field and the Confirm field. This password must be between 6 and 32 characters.
The default password is “public”.
• SNMPv3 Authentication Password: The password used when sending authenticated SNMPv3 messages. Enter a
password in both the Password field and the Confirm field. This password must be between 6 and 32 characters, but
a length of at least 8 characters is recommended. The default password is “public”. Secure Management (Services
tab) must be enabled to configure SNMPv3.
The default SNMPv3 username is administrator, with SHA authentication and DES privacy protocol.
• SNMPv3 Privacy Password: The password used when sending encrypted SNMPv3 data. Enter a password in both
the Password field and the Confirm field. This password must be between 6 and 32 characters, but a length of at
least 8 characters is recommended. The default password is “public”. Secure Management (Services tab) must be
enabled to configure SNMPv3.
• Telnet (CLI) Password: The password for the CLI interface (via serial or Telnet). Enter a password in both the
Password field and the Confirm field. This password must be between 6 and 32 characters. The default password is
“public”.
• HTTP (Web) Password: The password for the Web browser HTTP interface. Enter a password in both the Password
field and the Confirm field. This password must be between 6 and 32 characters. The default password is “public”.
NOTE: For security purposes Proxim recommends changing ALL PASSWORDS from the default “public” immediately, to
restrict access to your network devices to authorized personnel. If you lose or forget your password settings, you
can always perform the Reset to Factory Default Procedure.