User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 81
Parameter Description
Rule Name This parameter specifies the Name of the Packet Identification Rule
(PIR) and can have a length of 1-32 characters.
ToS Rule This parameter is used to enable/disable TOS rule. Enter the values
for the following to specify the ToS-related configuration:
ToS Low
ToS High
ToS Mask
Ether Priority Rule This parameters is used to enable or disable 802.1p priority rule.
Enter the values for the following to specify 802.1p priority
configuration:
Priority Low
Priority High
VLAN Rule This parameters allows to enable or disable VLAN rule. Enter the
VLAN ID when the VLAN rule is enabled.
PPPoE Encapsulation This parameter is used to classify PPPoE traffic.
NOTE:
• Enabling/disabling PPPoE Configuration will
automatically disable Ether Type Rule. User can
configure it again by enabling Ether Type Rule.
• When PPPoE Encapsulation is enabled, incoming
packet will be checked again Ether value “0x8864” and
look for PPPoE Protocol Id value “0x0021”(IP Protocol)
by default. User can modify the PPPoE Protocol Id. All
other classification rules which are specified in the PIR
rule will work only if the PPPoE Protocol Id is “0021”.
• Ether Value is not valid when PPPoE Encapsulation is
enabled.
Ether Type Rule This parameters is used to enable/disable Ether Type rule. Enter the
values for the following to specify the Ether Type rule related
configuration:
Ether Type
PPPoE Protocol Id
Ether Value
NOTE:
• PPPoE Protocol Id is not valid if PPPoE Encapsulation is
disabled.
• Ether Value is not valid if PPPoE Encapsulation is
enabled.