User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Preface
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 8
Preface
About this Manual
Congratulations on your purchase of Tsunami QuickBridge 8100. This manual gives you a jump-start working knowledge
on the QuickBridge 8100 link that can help you build a wireless network backhaul application easily! It describes the
QB-8100 device installation and its functions, the technology used, and the recommended methods for configuring and
monitoring the device.
Audience
The intended audience for this manual are the Network Administrators who are installing and/or managing this device.
Prerequisites
The reader of this document should have working knowledge of Wireless Networks, Local Area Networking (LAN) concepts,
network access infrastructures, and client-server applications.
Related Documents
All other documents are included in CD ROM in both printed (PDF) and online (HTML) formats.
Product Covered in this Guide
Organization of this Manual
This manual documents installing and managing of Tsunami QB series. Before installing and using the unit, Proxim
recommends you to read the following chapters of this manual:
• Chapter 1 Overview: Provides an overview of Tsunami QB-8100 as well as wireless network topologies and
combinations that can be built with the unit.
• Chapter 2 Installation and Initialization: Provides detailed installation instructions and explains how to access the
device for configuration and maintenance.
• Chapter 3 Basic Configuration: Provides a high-level overview of system features, explains how to navigate the user
interface, and discusses the most common settings for managing the unit.
• Chapter 4 Advanced Configuration: Explains the Web Interface’s “Configure” options in a hierarchical manner, so
you can easily find details about each item.
• Chapter 5 System Management: Explains the Web Interface’s “Management” options in a hierarchical manner, so
you can easily find details about each item to effectively manage the device.
• Chapter 6 Monitoring the System: Explains the Web Interface’s “Monitor” options in a hierarchical manner, so you
can easily find details about each item.
• Chapter 7 Procedures: Provides details about the various procedures involved in the operation of the QB-8100 units
using the Web interface.
• Chapter 8 Troubleshooting: Provides instructions and solutions to solve the issues you may encounter while
installing and using the QB-8100 units.
Product Description
Tsunami QB-8150-LNK-100&5 -XX
Two Tsunami QB 8150 Links, 100 & 5 Mbps, MIMO 2x2,
16 dBi Integrated antenna